# Tyre degradation modelling and stint length

> Measure how tyres perform over their life during practice long runs, separate degradation from fuel and driver effects, and use a simple model to choose stint lengths and the number of stops.

Area: Race Engineering & Strategy · Starting level: L2 Practitioner · Updated 2026-11-16
Source page: https://race-engineer-academy.vercel.app/lesson/strategy-tyre-degradation-stint-length

## L1 · Foundation

**Tyres don't deliver constant performance.** Over a stint the overall grip falls, and if one axle wears faster the balance changes. To plan a race you need to know (Segers §16.2.2):

- How many laps from new until the tyre reaches peak performance?
- In which lap is the highest grip recorded?
- From the peak, how fast does performance fall (seconds per lap)?
- What is the realistic maximum life before a "cliff"?
- Which way does the balance drift (understeer or oversteer)? Which axle wears most?
- What is the average lap time over the life of the set?

**Typical life phases:**
1. **Warm-up** (1–3 laps): pressures and temperatures rise into the window.
2. **Peak** (often lap 2–4 on slicks).
3. **Steady degradation**: roughly linear loss from wear and heat cycles.
4. **Cliff**: rapid loss when the tread is worn or the compound overheats permanently.

**Get the data in practice.** Run long stints on representative fuel loads, and log tyre mileage for every set used (including qualifying sets). Plot lap time and a grip metric against tyre laps: the best (lowest) lap-time envelope traces the degradation curve; scatter above it comes from fuel, traffic and driver.

## L2 · Practitioner

**Separating effects.** Over a stint three things change together: fuel burns (faster), tyres degrade (slower), the driver adapts. Segers' Dubai example: in a 3-hour GT race the first driver suffered understeer for the first ~30 % of the stint, set his fastest lap on lap 3, lost ~1.3 s over the first ten laps, then adapted and returned to near-best times, before losing significant time in the last quarter (after ~24 laps) as wear set in.

Model each lap as

$$t(n) = t_0 + k_{fuel}\,m_{fuel}(n) + \Delta t_{tyre}(n_{tyre}) + \varepsilon$$

Fuel-correct first ($t - k_{fuel} m_{fuel}$), then fit $\Delta t_{tyre}$ – usually linear: $\Delta t_{tyre} = d\cdot n_{tyre}$, optionally with a warm-up term and a cliff.

**Typical degradation rates** (fuel-corrected, dry): GT3 on a durable compound ~0.03–0.1 s/lap; junior single-seaters on softer Pirelli compounds 0.05–0.2 s/lap depending on track abrasiveness and temperature. Measure your own: they vary hugely with track temperature and setup.

**Stint length decision factors:**
- Fuel range (refuelling races) – often the binding limit in GT/prototype endurance.
- Tyre performance – when does staying out cost more than a stop?
- Regulations – maximum driver stint time, minimum drive time, tyre allocation, mandatory stops.
- Track position and traffic.

**Double-stinting** (two fuel stints on one tyre set) is standard in many endurance races when deg is low: it saves the tyre-change time and preserves the allocation. Check the fuel-corrected lap times of the second stint to confirm it pays.

**Balance drift.** Track average understeer angle per lap through stints: if the car drifts to understeer as fronts wear, a setup that starts slightly oversteery can give a better *average* stint. Tyre-pressure targets must be set for the hot stabilised condition, not lap 1.

## L3 · Advanced

**How many stops? A first-order model.** Let the race be $L$ laps, degradation linear at $d$ s/lap per lap of tyre age, and pit loss $P$ seconds. With $S$ equal stints, the tyre time lost per stint is about $d\,\ell^2/2$ with $\ell = L/S$, so total time is

$$T(S) \approx \frac{d\,L^2}{2S} + (S-1)P$$

Setting $dT/dS = 0$:

$$S^* = L\sqrt{\frac{d}{2P}}$$

Example: $L$ = 60, $d$ = 0.05 s/lap², $P$ = 22 s → $S^* = 60\sqrt{0.05/44} \approx 2.0$ → a one-stop (two stints). Check neighbours: 1 stint 90 s; 2 stints 45 + 22 = 67 s; 3 stints 30 + 44 = 74 s. The optimum is often flat – small differences between strategies – so track position, traffic and SC risk decide.

**Refinements:**
- **Warm-up/out-lap penalty** – add a fixed cost per new set (cold tyres, 1–3 s for hard compounds in cool conditions).
- **Non-linear degradation** – thermal deg can be partly recoverable (driver manages temperatures), wear deg is not; a cliff sets a hard maximum.
- **Compound offset** – a softer compound may be 0.5–1.0 s faster on fresh tyres but degrade faster. With offset $o$ and degradation rates $d_s > d_h$, the soft is slower *per lap* after $n_x = o/(d_s - d_h)$ laps, but it banked time early, so over a whole stint from new it stays the faster choice up to $\ell_x = 2o/(d_s - d_h) = 2n_x$ laps (linear deg, equal warm-up). Do not confuse the two crossovers.
- **Fuel interaction** – heavy-fuel laps are slow anyway and load tyres more; deg often looks worse early in a stint.
- **Track evolution** – rubber laid down improves times by 0.01–0.05 s/lap in early race laps, masking degradation; compare against cars on different strategies to separate.

**Using practice data well.** Practice long runs rarely have race fuel and race conditions. Normalise: fuel-correct, temperature-correct (track temperature sensitivity of degradation), and compare tyre-life curves from several sets (lower envelope of lap time vs tyre mileage, as Segers shows). Keep a database across events – degradation per track and compound is one of the most valuable strategic assets a team has.

## L4 · Expert

**From models to decisions under uncertainty.** Real strategy tools run Monte Carlo simulations of the race: each car's pace, degradation and pit loss with uncertainty, overtaking models (a car needs a pace advantage of ~0.5–1.5 s/lap to pass depending on the track), and stochastic safety cars. The output is a distribution of finishing positions per strategy, not a single answer.

Key sensitivities to keep in mind:
- **Degradation uncertainty dominates** early-weekend strategy; update $d$ continuously from race laps (yours and rivals') with a Bayesian-style approach – weight new laps more as they accumulate.
- **Thermal management interacts with driving**: telling a driver to manage tyres (lower slip, smoother inputs) can reduce $d$ at a lap-time cost; this is effectively choosing a point on a pace–degradation curve. The optimum push level depends on stint length remaining: push when few laps remain, manage early in a long stint.
- **Allocation constraints** (limited sets per weekend) mean practice and qualifying use must be planned backwards from the race needs.

## Key formulas

**Stint lap-time model**

$$t(n) = t_0 + k_{fuel}\,m_{fuel}(n) + d\,n_{tyre} + \varepsilon$$

- d: degradation rate (s/lap per lap of tyre age)
- n_{tyre}: tyre age (laps)

**Total race time vs number of stints (linear deg)**

$$T(S) \approx \frac{d\,L^2}{2S} + (S-1)\,P$$

- L: race laps
- S: number of stints
- P: pit loss (s)

**Optimum number of stints**

$$S^* = L\sqrt{\frac{d}{2P}}$$


## Trackside takeaways

- Fuel-correct lap times before judging degradation.
- Log tyre mileage for every set; plot the lower envelope of lap time vs tyre laps.
- Optimum stints ≈ L·√(d/2P); the optimum is often flat, so track position and SC risk decide.
- Double-stinting pays when fuel-corrected second-stint times stay close to the first.
- Track balance drift through stints; design setup for the average stint, not lap 1.

## By car category

### GT3

Durable compounds and refuelling make fuel range the usual stint limiter; double/triple stints on tyres are common in 24h races when track temperature allows.

### FIA F2

Feature race: two dry compounds must both be used, so stop timing is a degradation trade-off between option and prime; sprint race runs without a stop.

### FIA F3

Single dry compound and no mandatory stop: tyre management over the full race distance is the key; degradation analysis guides how hard to push early.

### Hypercar (LMH/LMDh)

Limited tyre allocation per race drives multi-stinting; balance drift with energy and fuel load is closely tracked.

### IndyCar

Primary vs alternate compounds on road/street courses: alternates are faster but degrade more; stint planning around cautions is crucial.

### Super Formula

Mandatory tyre change in the race: undercut/overcut decisions depend on warm-up of the fresh set and degradation of the old one.

## References

- Segers, Analysis Techniques for Racecar Data Acquisition, 2nd ed. (SAE 2014): §16.2 Lap Time Variation During a Race (§16.2.2 Tire Wear)
- Segers, Analysis Techniques for Racecar Data Acquisition, 2nd ed. (SAE 2014): §2.2.5 Run Charts
- Milliken & Milliken, Race Car Vehicle Dynamics (SAE 1995): Ch. 2 Tire Behavior
