# Wheel rate, tyre rate & ride rate (springs in series)

> The spring on the damper is not the stiffness the tyre sees. Motion ratio turns spring rate into wheel rate, and the tyre acts as a second spring in series, giving the ride rate that actually sets body frequency.

Area: Springs, Anti-roll Bars & Heave · Starting level: L1 Foundation · Updated 2026-11-16
Source page: https://race-engineer-academy.vercel.app/lesson/springs-wheel-tyre-ride-rate

## L1 · Foundation

### Three stiffnesses, one corner
A race car corner has (at least) two springs between the body and the track:

1. **The suspension spring**, mounted on the damper, usually driven through a pushrod/rocker or directly by the wishbone. Its catalogue rate $k_s$ (N/mm) is what you write on the setup sheet.
2. **The tyre**, which is itself a stiff air spring with a vertical rate $K_t$ of roughly **250–450 N/mm** for a racing slick.

The spring does not move as much as the wheel. The **motion ratio** $\mathrm{MR}$ = spring travel / wheel travel (typically 0.6–1.0). Because the lever reduces both the travel *and* the force seen at the wheel, the **wheel rate** scales with the square:

$$K_w = k_s\,\mathrm{MR}^2$$

A 200 N/mm spring at $\mathrm{MR}=0.8$ is only 128 N/mm at the wheel.

The suspension and tyre are **in series** – the same load passes through both, and their deflections add. Series springs combine like resistors in parallel:

$$K_r = \frac{K_w K_t}{K_w + K_t}$$

$K_r$ is the **ride rate**: the stiffness between the sprung mass and the road. It is always *lower* than the softer of the two.

### Typical numbers
GT3 front: $k_s$ = 200 N/mm, MR = 0.9 → $K_w$ = 162 N/mm. Tyre 360 N/mm → $K_r$ ≈ 112 N/mm. The tyre takes about a third of the ride deflection. On formula cars with stiffer springs the tyre takes more than half.

**Why you care:** every frequency, roll-stiffness and platform calculation you do later must use the correct rate – using spring rate instead of ride rate is the most common first-season mistake.

## L2 · Practitioner

### Getting the rates right trackside
**Motion ratio** comes from the kinematics model or a simple measurement: jack the wheel (spring removed or replaced by a solid link), log wheel travel vs damper travel at 5 mm steps through the working range. The slope is MR. If the damper is inclined to the wheel's path, the cosine of that angle is already contained in a measured MR – don't apply it twice. Remember MR is generally not constant: rocker geometry gives a rising or falling rate over travel; use the value at the *dynamic* ride height, not at full droop.

**Tyre rate** depends on pressure (rises roughly linearly – a few % per 0.1 bar), construction, load, camber, temperature and speed. Typical vertical rates:

| Tyre | Approx. $K_t$ |
|---|---|
| F4 slick | 200–260 N/mm |
| GT3 / LMP2 slick | 300–420 N/mm |
| F2 / SF / IndyCar slick | 300–400 N/mm |

Use the manufacturer's data (at hot pressure) if available; rig data or a data-logging method otherwise: wheel load from pushrod load cells (Segers §10.6) plotted against tyre deflection, taken as laser ride height minus the pot-derived ride height (Segers §13.4.2).

**Practical consequences**
- Doubling the spring does *not* double the ride rate. F3 example: $K_w$ = 250 → 500 N/mm with $K_t$ = 300 N/mm changes $K_r$ from 136 → 188 N/mm, only +38 %.
- A **tyre pressure change is a stiffness change**. In ride, a 10 % tyre-rate change is worth about $10\,\% \cdot K_w/K_t$ of wheel rate: ≈4–5 % on a GT3 ($K_w < K_t$), 10–20 % on a stiff aero car. Segers' roll-ratio example (one car, one metric) needed +25 % rear wheel rate to undo a 10 % rear tyre-rate change. When you change compound/construction or run pressures 0.2 bar off-target, your spring setup has effectively changed.
- When comparing to another team's sheet, compare **wheel rates**, not spring rates – the motion ratios may differ.
- Bump rubbers, heave springs and ARBs add *in parallel* with the corner spring before the tyre is put in series.

**Pitfall:** Segers and several data tools define motion ratio the other way round (wheel/spring > 1), giving $K_w = k_s/\mathrm{MR}^2$. Always check which convention a sheet uses.

## L3 · Advanced

### Parallel and series networks, and what really sets the rate
Build the corner as a network: in parallel at the wheel, the corner spring $k_s\mathrm{MR}_s^2$, the bump-stop rate $k_{bs}(x)\mathrm{MR}_s^2$ when engaged, a share of the ARB (roll only) and of the heave element (heave only). In series with that, the **tyre** and also the **compliance of the suspension itself** – wishbone bending, rocker and pushrod stretch, bearing slop, upright and chassis pick-up flex. On many cars the structure is "only" 3000–10000 N/mm, which still removes several % of a stiff wheel rate. Rig-measured wheel rates are therefore 3–10 % below the calculated $k_s\mathrm{MR}^2$ on stiffly sprung formula cars.

Because series compliances add,

$$\frac{1}{K_r} = \frac{1}{K_w} + \frac{1}{K_t} + \frac{1}{K_{struct}}$$

the softest element dominates. On a high-downforce car with wheel rates of 400–600 N/mm, the tyre is the softest element in heave, so tyre pressure, construction and even tyre temperature drive the body frequency more than a 20 % spring change. That is why aero platform work starts from a good tyre model.

**Non-constant motion ratio.** With a rocker, $\mathrm{MR}(z)$ varies with wheel travel $z$; the instantaneous wheel rate is

$$K_w(z) = k_s\,\mathrm{MR}(z)^2 + F_s\,\frac{d\,\mathrm{MR}}{dz}$$

The second term (spring force times rate of change of MR) is often forgotten – with a large preload or a strongly rising rocker it can be 10–20 % of the total and is how "progressive" rockers stiffen the car as aero load compresses it.

**Tyre rate is not a constant either.** It rises with pressure and, mildly, with deflection/load (the load–deflection curve of a slick is near-linear and slightly progressive); the rolling tyre differs from a static pad measurement, and warm tyres are softer than cold ones at the same pressure. Expect ±10 % across a stint as pressures build. Using static cold numbers can mis-predict body frequency by 5 %.

**Measuring.** Compare the theoretical ride rate to the rate inferred on track: ride-height laser (body to ground) vs pushrod load (or modelled load from damper position × wheel rate) gives the total; pot displacement gives the suspension share; the difference is tyre (+ structure) deflection.

## L4 · Expert

### Edge cases a simulation engineer must handle
**Single-wheel vs heave vs roll rate.** "Wheel rate" is mode-dependent once an ARB or third element is fitted. For a single-wheel input the ARB contributes about **half** its roll-mode wheel rate (the opposite wheel stays put, so the bar twists half as much) and a heave element contributes about a **quarter** of its axle heave rate. Kerb compliance therefore depends strongly on how much of the axle stiffness you carry in ARB/third spring vs corner springs.

**Tyre damping and hysteresis.** The tyre is a spring with very low damping (ζ ≈ 0.03–0.05 on its own). Every mode in which the tyre is the dominant compliance (wheel hop, the race-car roll mode, the heave mode of very stiff aero cars) is poorly damped by the tyre and must be controlled by the damper *through* the suspension – which becomes ineffective when the suspension is much stiffer than the tyre. This is the fundamental limit on how stiff you can spring a car: past a wheel-rate/tyre-rate ratio of roughly 1:1 the damper "sees" less and less of the motion and contact patch load variation rises.

**Aero stiffness.** Downforce depends on ride height. Over most of the map downforce *rises* as the car gets lower ($\partial F_z/\partial h < 0$), so the aero "spring" is destabilising: the net heave stiffness is $K_{net} = K_{mech} + \partial F_z/\partial h$, i.e. *less* than the mechanical rate. Near the ground-effect stall the slope changes abruptly. On F2/SF23/hypercar platforms the aero term can be tens of N/mm per axle at speed – enough to shift heave frequency by 5–10 % – and around the stall the downforce–height curve plus its time lag can feed energy into the heave mode (effectively negative damping): porpoising.

**Series stiffness in roll** with chassis torsion is handled in the roll-stiffness lesson; the same rule (series compliances add) applies, and a torsionally soft chassis caps the roll-stiffness distribution range you can achieve with bars.

## Key formulas

**Wheel rate**

$$K_w = k_s\,\mathrm{MR}^2,\qquad \mathrm{MR} = \frac{\Delta x_{spring}}{\Delta z_{wheel}}$$

- K_w: wheel rate (N/mm)
- k_s: spring rate (N/mm)
- MR: motion ratio, spring travel / wheel travel (–)

**Ride rate (series)**

$$K_r = \frac{K_w K_t}{K_w + K_t}$$

- K_r: ride rate (N/mm)
- K_t: tyre vertical rate (N/mm)

**General series network**

$$\frac{1}{K_r} = \frac{1}{K_w} + \frac{1}{K_t} + \frac{1}{K_{struct}}$$

- K_{struct}: structural compliance of links, rocker, upright, pick-ups (N/mm)

**Wheel rate with variable motion ratio**

$$K_w(z) = k_s\,\mathrm{MR}(z)^2 + F_s\,\frac{d\,\mathrm{MR}}{dz}$$

- F_s: spring force (N)
- z: wheel travel (mm)

## Trackside takeaways

- Wheel rate = spring rate × MR² (with MR = spring/wheel travel). Check which MR convention the sheet uses.
- Tyre and suspension are in series: ride rate is always below both. Use ride rate for frequencies.
- Tyre rate ~250–450 N/mm on slicks; on stiff aero cars the tyre is the softest spring in heave.
- A tyre pressure / construction change is a stiffness change: in ride, 10 % tyre rate ≈ 10 %·(K_w/K_t) of wheel rate (≈4–5 % on a GT3, 10–20 % on a stiff aero car); Segers' roll-ratio example needed +25 % wheel rate.
- Compare setups across cars in wheel rate, never spring rate.

## By car category

### GT3

Coil-over corner springs, MR ~0.8–1.0 at the front, often lower at the rear. Typical wheel rates ~120–250 N/mm; tyre ~320–400 N/mm, so the tyre takes 30–45 % of ride deflection. Bump stops add a large parallel rate at speed.

### One-make Cup

Springs are frequently spec or chosen from a small homologated list – the tyre pressure window is your real ride-rate adjuster. Keep hot pressures on target before judging any spring/bar change.

### TCR

MacPherson front: MR close to 1 but strut friction and side-load add hysteresis that a pure rate calculation misses. Rear twist-beam/multilink cars have very different single-wheel vs roll rates.

### Formula 4

Low-power, low-downforce cars on relatively soft springs: tyre is stiffer than the suspension, so spring changes are effective and felt directly.

### FIA F3

Stiff pushrod suspension with heave element: in heave the tyre (≈300 N/mm) is softer than the suspension, so pressures strongly affect platform and ride height at speed.

### LMP2

Third elements and stiff corner springs; tyre compliance and structural compliance both matter. Use rig- or data-derived ride rates rather than catalogue rates for aero-map work.

### IndyCar

Road-course setups run very stiff heave rates; tyre rate (which changes with Firestone compound and pressure) is a key parameter in ride-height prediction at Long Beach-type bumpy tracks.

## References

- Milliken & Milliken, Race Car Vehicle Dynamics (SAE 1995): Ch. 16 Ride and Roll Rates
- Milliken & Milliken, Race Car Vehicle Dynamics (SAE 1995): Ch. 21 Suspension Springs
- Milliken & Milliken, Race Car Vehicle Dynamics (SAE 1995): Ch. 23 Compliances
- Segers, Analysis Techniques for Racecar Data Acquisition, 2nd ed. (SAE 2014): §9.3 Using Roll Gradients as a Setup Tool (wheel rate from spring rate and motion ratio (inverse MR convention))
- Segers, Analysis Techniques for Racecar Data Acquisition, 2nd ed. (SAE 2014): §9.4 Front to Rear Roll Angle Ratio (worked example: +10 % rear tyre rate needs ≈ +25 % rear wheel rate to restore the roll ratio)
- Segers, Analysis Techniques for Racecar Data Acquisition, 2nd ed. (SAE 2014): §10.6 Measuring Wheel Loads with Suspension Load Cells
- Segers, Analysis Techniques for Racecar Data Acquisition, 2nd ed. (SAE 2014): §10.7 Tire Spring Rates (tyre springs act in series with the suspension springs)
- Segers, Analysis Techniques for Racecar Data Acquisition, 2nd ed. (SAE 2014): §13.4 Ride Height Measurement (tyre deflection = laser ride height minus suspension ride height)
