# Ride frequency and how to choose it

> Ride frequency normalises stiffness by sprung mass so cars of different weight can be compared. Choosing it is a trade between mechanical grip over bumps and aero platform control, with the front/rear ratio shaping pitch behaviour.

Area: Springs, Anti-roll Bars & Heave · Starting level: L1 Foundation · Updated 2026-11-16
Source page: https://race-engineer-academy.vercel.app/lesson/springs-ride-frequency

## L1 · Foundation

### Natural frequency of the body on its springs
Treat one corner as the sprung mass $m_s$ (that corner's share of body, driver, fuel – excluding wheels, uprights, brakes and roughly half the links) sitting on the ride rate $K_r$. It oscillates at

$$f = \frac{1}{2\pi}\sqrt{\frac{K_r}{m_s}}$$

with $K_r$ in N/m and $m_s$ in kg. Frequency is a better language than spring rate because it is independent of the car's mass: "3 Hz" means the same stiffness *relative to the mass* on a 1300 kg GT3 and a 600 kg F4.

A useful intuition: the static deflection under 1 g is $\delta = g/(2\pi f)^2$. At 1 Hz (road car) that is ~250 mm; at 3 Hz ~28 mm; at 5 Hz ~10 mm. Race cars are stiff because they cannot afford the travel – geometry, aero and ground clearance all need a controlled platform.

### Indicative ride frequencies (mechanical corner rates incl. tyre)
| Category | Approx. ride frequency |
|---|---|
| Road car | 1.0–1.5 Hz |
| GT4 | 2.0–2.6 Hz |
| One-make cup / TCR | 2.5–3.2 Hz |
| GT3 | 2.8–3.6 Hz (plus bump stops at speed) |
| F4 | 3–4 Hz |
| LMP2 / Formula Regional | 3.5–4.5 Hz |
| Hypercar, F3/F2, SF, IndyCar road course (heave) | 4–6 Hz |

These are typical ranges, not rules – read your car's data.

**Rule of thumb:** more downforce → higher frequency, because a stiffer platform is needed to hold the ride height the aero was designed for.

## L2 · Practitioner

### Working with frequency trackside
**From frequency to spring.** Choose $f$, compute the required ride rate $K_r = m_s(2\pi f)^2$, back out the wheel rate from the series formula $K_w = K_rK_t/(K_t - K_r)$, then the spring $k_s = K_w/\mathrm{MR}^2$. The calculator does this chain. Get $m_s$ from corner weights minus estimated unsprung mass (GT3 ~45–60 kg per corner, formula cars ~25–40 kg).

Example – GT3 rear corner: corner weight 360 kg, unsprung 55 kg → $m_s$ = 305 kg. Target 3.2 Hz → $K_r$ = 305·(2π·3.2)² ≈ 123 N/mm. Tyre 360 N/mm → $K_w$ ≈ 187 N/mm. MR 0.8 → spring ≈ 292 N/mm.

**Front/rear frequency ratio.** On road cars, Olley's "flat ride" principle puts the rear frequency 10–20 % above the front so that after a bump the rear (which hits it later) catches up with the front and the body bounces rather than pitches. The delay is $L/V$: 2.7 m at 100 km/h is 97 ms, a big fraction of a 1 Hz period. At 250 km/h it is 39 ms vs a ~300 ms period for a 3.3 Hz race car, so the flat-ride argument is weak on a race car. Race engineers instead choose the ratio for:
- **Aero platform:** front ride height is usually the most sensitive aero parameter (splitter/front floor), so high-downforce cars often run the front stiffer in heave than the rear.
- **Traction:** a softer rear (lower frequency) helps a RWD car put power down over bumps.
- **Balance:** front/rear *heave* stiffness changes the mechanical balance only indirectly (via roll stiffness on cars without third springs, and via aero platform).

Typical front/rear ratios lie within ±15 % of 1.0.

**Pitfalls**
- Using wheel rate instead of ride rate (tyre forgotten) over-estimates frequency by a factor $\sqrt{1+K_w/K_t}$: ~10–25 % on GT cars, 40 %+ on stiff aero cars where $K_w \ge K_t$.
- On cars with ARBs and no third spring, raising corner springs also raises roll stiffness – check LLTD after any frequency change.
- On GT3, quoted spring frequencies ignore the bump stop: at high speed the effective frequency can be 30–60 % higher.

## L3 · Advanced

### Choosing the frequency – the real trade-off
The ride frequency is the outcome of three competing demands:

1. **Mechanical grip** wants low contact-patch load variation. On a bumpy surface, softer suspension (lower $f$) reduces tyre load fluctuation in the 2–10 Hz range – up to a point, after which body motion and travel limits dominate.
2. **Aero platform** wants small ride-height and pitch variation. The required heave stiffness follows directly from allowable ride-height change: $\Delta h = \Delta F_{aero}/K_{heave}$. E.g. a GT3 with ~3 kN extra rear downforce at Vmax on an axle heave ride rate of 2·110 = 220 N/mm drops ~14 mm – usually too much without bump stops, which is exactly why GT3s use them.
3. **Geometry and travel**: camber change, bump steer, damper travel and skid-block/plank wear limit total motion.

The optimum therefore scales with downforce: low-downforce cars sit near 2–3 Hz where mechanical grip dominates; high-downforce cars move to 4–6 Hz in heave and accept a mechanical-grip penalty because the aero gain is larger.

**Frequency vs damping.** Body frequency and damping must be chosen together. Doubling stiffness raises $f$ by √2 and lowers the damping ratio by 1/√2 for the same damper. A frequency change without a damper adjustment is a combined change.

**Heave vs pitch vs roll frequency.** The single-corner frequency is a simplification. The body has separate modes:
- **Heave** – all four corners together.
- **Pitch** – depends on the pitch inertia $I_y = m k^2$ and $K_f a^2 + K_r b^2$. The *dynamic index* $DI = k^2/(ab)$ is ~1 on many road cars (front and rear then act independently, which is Olley's assumption) but often **0.6–0.8 on race cars** where mass is centralised – the pitch mode is then *higher* than the heave mode and the corner-frequency picture under-predicts pitch stiffness. Segers reports equivalent pitch masses of 60–80 % of vehicle mass on race cars.
- **Roll** – roll inertia is small and roll stiffness (with bars) large, so roll "frequencies" are much higher; equivalent roll masses are only ~20–40 % of the car (Segers ch12).

**Measuring.** Verify on track: the PSD of ride-height or damper-position signals shows the body mode as a peak (see the frequency-domain lesson); a 4-post rig gives it directly.

## L4 · Expert

### Limits of the frequency concept
- **Amplitude dependence.** Real cars have friction, progressive bump stops, MR progression and aero stiffness. The "frequency" at 2 mm amplitude in a slow corner differs from that at 15 mm at Vmax. Quote frequency together with the operating point (speed, ride height, bump-stop engagement).
- **Speed dependence.** With ground-effect aero, net heave stiffness = $K_{mech} + \partial F_z/\partial h$, and $\partial F_z/\partial h$ is normally negative (more downforce as the car drops). The aero term alone therefore *lowers* the effective frequency with speed; near the stall region the aero response can also remove damping – porpoising is the extreme case. On cars running onto progressive stops, packers or rising-rate rockers the mechanical rise usually dominates (the GT3 case in the practitioner section), so the net frequency at speed can be higher or lower – measure it rather than assume.
- **Coupled modes.** With a cross-coupled stiffness ($K_fa \ne K_rb$), heave and pitch couple; the measured peaks are mixtures. Modal decomposition (heave = mean of four, pitch = front − rear, etc.) of the measured motion gives cleaner estimates than single-corner signals.
- **Tyre-dominated regime.** Once $K_w \gg K_t$, ride frequency asymptotes to $\frac{1}{2\pi}\sqrt{K_t/m_s}$ (≈ 6–7 Hz for a formula-car corner with ~300 N/mm tyres and 150–190 kg sprung mass; lower for a heavier prototype corner). Extra spring then buys platform only through reduced suspension travel, while the tyre-dominated mode becomes poorly damped. That ceiling is why ground-effect cars bottom out on stiffness and move to ride-height control via packers, heave stops and aero design rather than ever-stiffer springs.
- **Frequency ratio as a balance tool** is at best second order on race cars; changes in front/rear heave stiffness act on balance mostly through aero platform (front ride-height sensitivity) and through the roll stiffness of corner springs. Attribute a balance change to "frequency ratio" only after ruling those out.

## Key formulas

**Undamped ride frequency**

$$f = \frac{1}{2\pi}\sqrt{\frac{K_r}{m_s}}$$

- f: ride frequency (Hz)
- K_r: ride rate (N/m)
- m_s: sprung corner mass (kg)

**Required ride rate**

$$K_r = m_s\,(2\pi f)^2$$


**Wheel rate from ride rate**

$$K_w = \frac{K_r K_t}{K_t - K_r}$$

- K_t: tyre rate (N/m)

**Static deflection at 1 g**

$$\delta_{st} = \frac{g}{(2\pi f)^2}$$

- g: 9.81 m/s²

**Dynamic index**

$$DI = \frac{k_y^2}{a\,b}$$

- k_y: pitch radius of gyration (m)
- a, b: CG to front / rear axle (m)

## Trackside takeaways

- f = (1/2π)·√(K_ride / m_sprung); always include the tyre.
- Typical: GT4 ~2–2.6 Hz, GT3 ~2.8–3.6 Hz, LMP2 ~3.5–4.5 Hz, F3/F2/SF/IndyCar heave ~4–6 Hz.
- Frequency rises with downforce because the platform must hold ride height: Δh = ΔF_aero / K_heave.
- Flat-ride (rear > front) matters less at race speeds; race cars set the ratio for aero platform and traction.
- Stiffer springs with the same dampers = less damping ratio. Change both consciously.

## By car category

### GT3

Mechanical ride frequencies ~2.8–3.6 Hz, but bump stops carry much of the aero load at speed, so effective high-speed frequency is far higher. Spring choice is often for low-speed grip and kerbs; bump-stop gap/rate for platform.

### GT4

Softer cars (~2–2.6 Hz), little aero; frequency is chosen for mechanical grip and kerb compliance. Limited spring options under BoP.

### One-make Cup

Spring options are restricted; when allowed, teams run the stiffest option on smooth circuits and soften for bumpy/kerb-heavy tracks.

### TCR

FWD cars with high front weight: front frequency often lower than rear in spring terms but with a very stiff rear ARB; the rear axle is effectively stiff in roll to help rotation.

### LMP2

Heave springs give ~3.5–4.5 Hz in heave with softer corner springs. Front heave is chosen to protect front ride height (most sensitive aero parameter) at Vmax at Le Mans/Monza.

### Hypercar (LMH/LMDh)

Heavy cars (~1030 kg+) with significant downforce – heave frequencies ~4–5 Hz. Rules limit ride-height/platform tricks, so stiffness and packers are the main platform tools.

### Formula 4

About 3–4 Hz; very little downforce, so choose for mechanical grip – softer often faster on bumpy circuits.

### FIA F3

Heave frequencies ~4–5.5 Hz. The tyre is the softest element in heave; pressures matter for ride height.

### Super Formula

Very high downforce for weight; stiff heave platform (~5–6 Hz in heave) with comparatively compliant roll/single-wheel set via corner springs.

### IndyCar

Road/street courses run high heave stiffness for the underfloor; street circuits force compromises (bumps, kerbs) – often softer heave plus more packer gap.

## References

- Milliken & Milliken, Race Car Vehicle Dynamics (SAE 1995): Ch. 16 Ride and Roll Rates
- Milliken & Milliken, Race Car Vehicle Dynamics (SAE 1995): Ch. 21 Suspension Springs
- Segers, Analysis Techniques for Racecar Data Acquisition, 2nd ed. (SAE 2014): §12.6 Modal Frequency Issues (wheel-equivalent masses for roll (≈20–40 %) and pitch (≈60–80 %) on race cars)
