# Pitch gradient and the aero platform

> Pitch gradient (pitch angle per g of longitudinal acceleration) characterises how the platform moves under braking and traction. On aero cars it drives aero balance changes on entry and exit and is shaped by heave stiffness, bump stops and anti-geometry.

Area: Springs, Anti-roll Bars & Heave · Starting level: L2 Practitioner · Updated 2026-11-16
Source page: https://race-engineer-academy.vercel.app/lesson/springs-pitch-gradient-aero-platform

## L1 · Foundation

### Pitch per g
Under braking the car dives (front down, rear up); under acceleration it squats. The **pitch gradient** is the body pitch angle per g:

$$PG = \frac{d\theta}{d a_x}\quad [\mathrm{deg}/g]$$

It is the longitudinal twin of roll gradient. From damper pots you take average front and average rear wheel travel and divide their difference by the wheelbase:

$$\theta = \frac{180}{\pi}\arctan\left(\frac{\bar z_f - \bar z_r}{L}\right)$$

Segers' example pitch plot (Fig. 9.12) has a slope of about 0.2 °/g.

**Why it matters more than "comfort":** on a car with downforce, the aero balance depends strongly on **front ride height** and **rake** (rear minus front ride height). When the car dives under braking, the front gets closer to the ground, front downforce typically increases and the aero balance moves forward → the rear goes light → **high-speed braking instability / entry oversteer**. On exit, squat raises the front → front loses downforce → **exit understeer**.

So the pitch platform is set to keep the aero balance in a narrow window through braking, cornering and acceleration. Tools: front/rear heave stiffness (springs, third springs), bump stops/packers, dampers (rate of pitch), and anti-dive/anti-squat geometry.

**Rule of thumb:** a car that is stable in slow-corner braking but nervous in high-speed braking often has an aero-platform (pitch) issue rather than a brake-balance issue.

## L2 · Practitioner

### Measuring and using pitch gradient
**Channels**
- Average front wheel travel $\bar z_f = (x_{LF}+x_{RF})/(2\mathrm{MR}_f)$, same at rear.
- Pitch angle as above; plot vs longitudinal g (X–Y) and fit separately for **braking** and **acceleration** – the two slopes differ because anti-dive ≠ anti-squat and because different bump stops engage.
- Better still on aero cars: **ride-height lasers** front and rear give the true aerodynamic ride heights (including tyre deflection). Build front RH, rear RH and rake channels and plot them vs speed and vs $a_x$.

**Pitch is not linear.** Segers notes that pitch gradient is rarely linear with anti geometry, and bump stops engaging under braking create a clear knee. Fit piecewise or use the slope over the range that matters (e.g. 1.0–2.0 g braking on a GT3).

**Static approximation**
$$\theta\,[\mathrm{deg}] \approx \frac{180}{\pi}\cdot\frac{m a_x h}{L^2}\left(\frac{1-AD}{K_{w,f}} + \frac{1}{K_{t,f}} + \frac{1-AL_r}{K_{w,r}} + \frac{1}{K_{t,r}}\right)$$
for braking with anti-dive fraction $AD$ at the front and anti-lift fraction $AL_r$ at the rear, all rates per axle (N/m) and $a_x$ in m/s². Anti-geometry only relieves the **suspension**: the links carry part of the load transfer, but the tyres still see the full $m a_x h/L$, so their deflection terms are not reduced. Pots see only the two suspension terms; ride-height lasers see all four. Stiffer heave or more anti → smaller suspension pitch; tyre pitch is set by tyre rate alone.

**Trackside levers**
| Symptom | Likely pitch cause | Levers |
|---|---|---|
| Unstable in high-speed braking | front dives, aero balance forward | more front heave/bump-stop support, less rear droop, more front LS bump damping |
| Exit understeer in fast corners | squat raises front | more rear heave/stop support, front rebound to hold the nose |
| Splitter/plank wear under braking | excessive dive | front packers/stops, higher static front |

**Pitfalls:** pitch measured from pots ignores tyre deflection – at 2 g braking the front tyres compress several mm more. For aero work use lasers or add modelled tyre deflection ($\Delta F_z/K_t$).

## L3 · Advanced

### Platform as an aero-mechanical system
The aero balance $AB = F_{z,f}/F_{z,total}$ is a function of front and rear ride height (the aero map). Linearised around the operating point:

$$\Delta AB \approx \frac{\partial AB}{\partial h_f}\Delta h_f + \frac{\partial AB}{\partial h_r}\Delta h_r$$

Sensitivities of a few tenths of a percent of front balance per mm of front ride height are common on GT and prototype cars; on ground-effect formula cars it can be larger, and strongly non-linear near the floor stall. In braking, $\Delta h_f$ is negative (dive) and $\Delta h_r$ positive (lift) – both usually move balance *forward*. Meanwhile speed is falling, so total downforce falls too and the car rises – the net ride-height trajectory through a braking zone is a combination of speed (aero load) and $a_x$ (pitch).

**Design choices**
- **Heave stiffness ratio & stops:** keep $\Delta h_f$ small during braking without making the front too stiff over braking bumps (lock-ups).
- **Anti-dive** reduces suspension dive but adds caster change and can make braking feel "wooden"; anti-squat similarly trades traction feel for platform. Many formula cars use little anti-dive for feel and rely on stiffness.
- **Dampers** control the *rate* of pitch: LS bump front / LS rebound rear on entry, the reverse on exit. Hold the platform through the transient, but they cannot change steady-state pitch.
- **Pitch inertia vs stiffness** – race cars with mass centralised have a pitch mode above heave (see ride frequency lesson); pitch response is fast and mostly quasi-static at braking-onset time scales (~0.2–0.3 s).

**Data metrics** to track per lap (Segers-style): pitch gradient braking, pitch gradient traction, min front RH in braking zones, rake at Vmax and at apex speed of the key fast corner. Run-chart them across the weekend alongside balance comments.

## L4 · Expert

### Subtleties
- **Pitch centre and measurement point.** Pitch from pots is a *suspension* pitch about an arbitrary point; aero cares about the floor's attitude and its height at the front of the plank/splitter. Translate measured front/rear heights to the aero reference points (often ahead of the front axle and at the diffuser) using geometry – a 0.2° pitch moves a splitter 1.5 m ahead of the CG by 5 mm.
- **Coupling to roll.** Combined braking + turning means the outside-front corner is lowest; the minimum floor height is at a corner, not on the centreline. Use a 3-laser or 4-laser setup or a modal heave/pitch/roll reconstruction to get the true minimum.
- **Anti-geometry non-linearity.** Anti percentages vary with travel; under big dive the anti may increase/decrease, and with pushrod geometry part of the brake reaction goes through the rocker, changing the effective wheel rate. Rig/K&C data is needed for accuracy.
- **Tyre growth.** At Vmax, tyre radius grows (more on bias-ply/large-sidewall tyres), raising ride height a few mm; combined with aero compression this changes the "real" platform. Laser data inherently includes it; static calculations do not.
- **Transient aero.** The flow under the floor takes time to respond; very fast pitch rates can produce aero balance transients that differ from the quasi-static map – one reason drivers sometimes report entry instability that steady-state sims don't show.

## Key formulas

**Pitch angle from wheel travel**

$$\theta = \frac{180}{\pi}\arctan\left(\frac{\bar z_f - \bar z_r}{L}\right)$$

- \bar z_f, \bar z_r: mean front / rear wheel travel, positive in bump (mm)
- L: wheelbase (mm)

**Pitch gradient**

$$PG = \frac{d\theta}{d a_x}\;[\mathrm{deg}/g]$$


**Quasi-static pitch in braking (simplified)**

$$\theta\,[\mathrm{deg}] \approx \frac{180}{\pi}\cdot\frac{m a_x h}{L^2}\left(\frac{1-AD}{K_{w,f}} + \frac{1}{K_{t,f}} + \frac{1-AL_r}{K_{w,r}} + \frac{1}{K_{t,r}}\right)$$

- h: CG height (m)
- a_x: longitudinal acceleration (m/s²)
- L: wheelbase (m)
- AD: front anti-dive fraction
- AL_r: rear anti-lift fraction
- K_{w}: axle suspension heave rate, wheel-referred, without tyres (N/m)
- K_{t}: axle tyre rate, sum of both tyres (N/m)

**Aero balance sensitivity**

$$\Delta AB \approx \frac{\partial AB}{\partial h_f}\Delta h_f + \frac{\partial AB}{\partial h_r}\Delta h_r$$

- AB: aero balance (front fraction)

## Trackside takeaways

- Pitch gradient = pitch angle per g, from front/rear average damper travel; fit braking and traction separately.
- On aero cars, dive under braking usually moves aero balance forward → high-speed entry instability.
- Heave stiffness, bump stops/packers and anti-geometry set pitch; dampers only set the rate.
- Use ride-height lasers (tyre deflection included) for aero platform; pots alone under-read pitch.
- High-speed vs low-speed braking stability difference = suspect platform before brake balance.

## By car category

### GT3

Front bump-stop gap and rubber are the main dive-control tools. Typical complaint: rear instability in high-speed braking (e.g. Spa Les Combes, Monza T1) fixed with more front support/less rear droop rather than brake balance.

### LMP2

Front heave packers and third damper control dive at Le Mans braking zones from 330 km/h; rake management is central to the aero setup.

### Hypercar (LMH/LMDh)

Heavy cars braking from high speed with hybrid regen on one axle – pitch platform and brake-by-wire balance interact.

### FIA F3

Floor sensitive to front ride height; heave packers set the dive limit. Watch plank wear after big braking zones.

### FIA F2

Large downforce changes through braking zones; platform discipline (pitch) directly affects entry stability.

### TCR

Little aero; pitch matters through geometry (camber/toe change on MacPherson) and weight transfer timing rather than aero balance.

### Super Formula

High aero sensitivity; heave elements and anti geometry tuned for minimal pitch through braking.

## References

- Segers, Analysis Techniques for Racecar Data Acquisition, 2nd ed. (SAE 2014): §9.7 Pitch Gradient
- Milliken & Milliken, Race Car Vehicle Dynamics (SAE 1995): Ch. 16 Ride and Roll Rates
- Milliken & Milliken, Race Car Vehicle Dynamics (SAE 1995): Ch. 15 Applied Aerodynamics (ride-height sensitivity of downforce/balance)
- Milliken & Milliken, Race Car Vehicle Dynamics (SAE 1995): Ch. 17 Suspension Geometry (anti-dive and anti-squat)
