# Heave / third springs: decoupling heave from roll

> A third (heave) element acts only when both wheels of an axle move together. It lets aero cars hold ride height under downforce with high heave stiffness while roll stiffness and single-wheel compliance are tuned separately.

Area: Springs, Anti-roll Bars & Heave · Starting level: L2 Practitioner · Updated 2026-11-16
Source page: https://race-engineer-academy.vercel.app/lesson/springs-heave-third-springs

## L1 · Foundation

### Why a third spring?
With only corner springs and ARBs, an axle has two stiffnesses you can tune:
- **Heave** (both wheels together): set by corner springs only.
- **Roll** (wheels opposite): corner springs + ARB.

An aero car needs very **high heave stiffness** – downforce of several kN would otherwise squash it onto the ground and wreck the aero map – but does not want correspondingly high stiffness for single-wheel bumps and kerbs. Stiff corner springs give both, plus roll stiffness you may not want.

A **third spring** (heave spring) is mounted between the two rockers of an axle (or on a separate rocker driven by both pushrods) so that it compresses only when both wheels rise together. In roll, one rocker moves up and the other down – the third element doesn't move.

So the stiffness "menu" becomes:

| Mode | Corner springs | ARB | Third spring |
|---|---|---|---|
| Heave | ✓ | – | ✓ |
| Roll | ✓ | ✓ | – |
| Single-wheel bump | ✓ | ~½ | ~¼ |

The car can then be stiff in heave (platform), stiff-ish in roll (aero attitude, balance via bars), yet relatively compliant to single-wheel inputs.

**Where you find them:** LMP2, hypercars, F3/F2, Super Formula, IndyCar, and many other prototypes. GT3/GT4/TCR/one-make cups use corner springs + ARBs + bump stops instead.

## L2 · Practitioner

### Working with heave elements trackside
**Axle heave rate** (wheel-referred):

$$K_{heave} = 2K_w + K_3\,\mathrm{MR}_3^2$$

with $\mathrm{MR}_3$ the third-element travel per unit of axle heave (both wheels moving together). Roll stiffness is unchanged by the third spring.

**Typical tools on a heave element**
- **Third spring rate** – sets platform stiffness under aero load.
- **Third (heave) packers / gap** – spacers that make the heave element (or a stiff bump rubber on it) engage after a defined travel. This is *the* ride-height-at-speed tool on F3/F2/LMP2/hypercars: you set static ride height for low-speed corners and the packer gap to stop the car going lower than X mm at Vmax.
- **Third damper** – controls heave/pitch motion independently of roll damping.
- **Preload** (on some designs) – changes where the element engages.

**Process**
1. From the aero map, find the target ride heights at high speed (e.g. front 15 mm, rear 45 mm at 280 km/h).
2. Estimate axle downforce at that speed; required heave stiffness or packer engagement follows from $\Delta h = \Delta F_{aero}/K_{heave}$.
3. Choose corner springs for single-wheel compliance (kerbs, bumps) and roll contribution; choose ARBs for balance.
4. Verify on track: ride height (laser) or heave from pots vs speed; check packer contact (pot ≥ gap) and minimum ride height / plank wear.

**Practical effects**
- Stiffer **front heave** → front holds height at speed → aero balance less likely to shift forward at Vmax, but stiffer over bumps/kerbs in braking.
- Stiffer **rear heave** → less rear squat on exit (traction trade-off) and smaller rake loss at speed.
- Changing heave stiffness alters *pitch* stiffness too: $K_{pitch} \approx K_{heave,f}a^2 + K_{heave,r}b^2$.

**Pitfall:** don't confuse "the car is stiff" comments. A driver complaining of harshness over kerbs on a heave-sprung car is often feeling ARB and corner-spring single-wheel stiffness, or packers engaged, not the heave spring.

## L3 · Advanced

### Mode stiffness algebra and design trade-offs
Write the axle stiffnesses (wheel-referred, per axle) with corner wheel rate $K_w$, ARB roll wheel rate $K_{arb}$ (force per wheel when wheels move equal-and-opposite), and third-element heave contribution $K_h = K_3\mathrm{MR}_3^2$:

$$K_{heave} = 2K_w + K_h,\qquad K_{\phi} = (K_w + K_{arb})\frac{t^2}{2},\qquad K_{single} \approx K_w + \tfrac{1}{2}K_{arb} + \tfrac{1}{4}K_h$$

(the single-wheel term follows from energy: one wheel moving $z$ twists the bar half as much as in roll and moves the third element by $z/2$.) This is the design space: three tuning variables, three mode stiffnesses. With only springs and bars, $K_{heave}$ and $K_{single}$ are tied; the third element breaks that coupling.

**Why heave and roll should be different on an aero car**
- Downforce is a heave (and pitch) load; lateral acceleration is a roll load. The ratio of aero load to lateral load is very different from a mechanical car, so the ideal ratio of heave to roll stiffness is too.
- Segers' modal analysis (ch12) emphasises that roll inertia is small and roll stiffness large on race cars, making the roll mode tyre-dominated and poorly damped. Being able to *lower* roll stiffness without losing heave stiffness can improve roll-mode load fluctuation.

**Warp.** The third spring does not resist warp (LF and RR up, RF and LR down), because each axle's wheel-sum is zero. Corner springs and ARBs do: in warp each axle is in roll, front and rear in opposite senses, so warp stiffness is roughly the series combination of front and rear roll stiffness (springs + bars, with tyres), in series with chassis torsion. A stiff bar package therefore makes the car stiff in warp. Diagonal load change over kerbs and cambered braking zones, and corner-weight sensitivity to perch changes, all scale with it. Only interconnected (e.g. hydraulic) systems can set warp stiffness independently of roll.

**Packers as non-linear heave stiffness.** A heave packer engaged at a given travel makes $K_{heave}$ piecewise: low below the gap (mechanical grip in slow corners), high above (platform at speed). The trade: a car riding on its packers has very high heave rate and poor compliance – lap-time sensitivity to kerbs and bumps rises sharply. Optimum gap is track-specific: smooth high-speed tracks (Monza, Paul Ricard) favour small gaps; bumpy ones (Sebring, street circuits) favour more gap and softer elements.

## L4 · Expert

### Beyond springs: interconnection, inerters and aero coupling
- **Inerters (J-dampers)** – a mass-like element on the heave axis producing force proportional to relative acceleration. Used in F1 historically to tame tyre-dominated heave modes and wheel-hop; banned or restricted in many series. Their existence tells you where heave-mode damping runs out: when the suspension is stiffer than the tyre, a conventional damper can't control the tyre mode.
- **Hydraulic interconnection** (e.g. Creuat-style systems, Segers ch12 author) can set heave, roll, pitch and warp stiffness/damping independently – the general case of what the third spring partially achieves. Mostly banned in top formulae, but the modal thinking is universal.
- **Aero-heave coupling.** On ground-effect cars the net heave stiffness is $K_{heave} + \partial F_z/\partial h$, where the derivative is negative (downforce increasing as height falls). Where its magnitude is large (venturi floor close to the ground) the net stiffness drops sharply, and around the stall the lagging aero response can act as negative damping → porpoising/bouncing. Packers and high heave stiffness are partly an answer to this, at the cost of mechanical compliance; the aero designer and the vehicle dynamicist must agree the ride-height window together.
- **Pitch/heave cross-coupling.** If $K_{heave,f}a \ne K_{heave,r}b$, a pure heave force (downforce at the CP) also pitches the car. Placing the aero centre of pressure and setting front/rear heave stiffness so the car descends *parallel* (constant rake) at speed is a classic platform objective: the required ratio is $K_{ride,f}/K_{ride,r} = F_{aero,f}/F_{aero,r}$ for equal ride-height drop – i.e. heave *ride-rate* distribution ≈ aero balance. Ride height includes tyre deflection, so these are axle heave rates **with the tyres in series**; if the front and rear tyre rates are not in the same ratio, the suspension heave rates must differ from the aero ratio. Setting the suspension rates alone to the aero ratio leaves a rake change at Vmax.

## Key formulas

**Axle heave rate with third element**

$$K_{heave} = 2K_w + K_3\,\mathrm{MR}_3^2$$

- K_3: third spring rate (N/mm)
- MR_3: third-element travel per unit axle heave

**Axle roll stiffness (third element absent)**

$$K_\phi = (K_w + K_{arb})\,\frac{t^2}{2}$$

- K_{arb}: ARB rate per wheel in roll (N/m)

**Single-wheel rate (approx.)**

$$K_{single} \approx K_w + \tfrac{1}{2}K_{arb} + \tfrac{1}{4}K_3\mathrm{MR}_3^2$$


**Ride-height drop under aero load**

$$\Delta h = \frac{\Delta F_{aero}}{K_{heave}}$$

- \Delta F_{aero}: axle downforce increase (N)
- K_{heave}: axle heave rate – use the ride rate (tyres in series) when Δh is ride height

**Parallel descent (constant rake)**

$$\frac{K_{ride,f}}{K_{ride,r}} = \frac{F_{aero,f}}{F_{aero,r}},\quad K_{ride} = \frac{K_{heave}K_{t,axle}}{K_{heave}+K_{t,axle}}$$

- K_{ride}: axle heave ride rate, suspension in series with tyres (N/mm)
- K_{t,axle}: sum of the two tyre rates on the axle (N/mm)

## Trackside takeaways

- Third spring acts in heave only; ARB in roll only; corner springs in both.
- Single-wheel stiffness ≈ K_w + ½ ARB + ¼ heave element – that is what the driver feels over kerbs.
- Heave packers/gap are the main ride-height-at-speed tool on prototypes and FIA formula cars.
- Heave ride-rate ratio front/rear (tyres included) ≈ aero load ratio front/rear for constant rake at speed.
- Heave changes also change pitch stiffness – check braking/accel platform.

## By car category

### GT3

No third element. Platform comes from corner springs plus bump stops (and their gaps), which also act in roll – a key difference from prototypes.

### LMP2

Front and rear third elements (spring + damper + packers). Le Mans setups use larger heave stiffness/packers for the long straights; Sebring/bumpy tracks need more gap.

### Hypercar (LMH/LMDh)

Heave elements central to platform control on these heavy cars; the rules restrict interconnection, so heave springs + packers + dampers do the job.

### FIA F3

Heave spring and packers are key FIA F3 tools; the floor is ride-height sensitive. Typical work: set packer gap so front minimum ride height at Vmax just avoids plank wear limits.

### FIA F2

Similar philosophy to F3 with more downforce; heave packers set Vmax ride height, corner springs/bars tuned for kerbs and balance.

### Super Formula

High downforce with heave elements; Suzuka-style high-speed tracks need tight heave control.

### IndyCar

Third springs and packers on road/street courses; the underfloor is sensitive, so heave stiffness vs bump compliance on street courses is a constant compromise.

### LMP3

Simpler suspension than LMP2; check homologation for heave element availability – many setups rely on corner springs, bars and bump rubbers.

## References

- Milliken & Milliken, Race Car Vehicle Dynamics (SAE 1995): Ch. 16 Ride and Roll Rates
- Milliken & Milliken, Race Car Vehicle Dynamics (SAE 1995): Ch. 21 Suspension Springs
- Segers, Analysis Techniques for Racecar Data Acquisition, 2nd ed. (SAE 2014): §12.5 Modal Analysis (heave/pitch/roll/warp modes and modal stiffness matrix)
