# Motion ratio & installation ratio

> The spring, damper and anti-roll bar never sit at the wheel. The motion ratio converts what they do into what the tyre feels – and because it enters squared, small geometry errors become large rate errors.

Area: Suspension Geometry & Kinematics · Starting level: L1 Foundation · Updated 2026-11-17
Source page: https://race-engineer-academy.vercel.app/lesson/sg-motion-ratio

## L1 · Foundation

**The spring is not at the wheel.** On almost every race car the spring and damper are mounted part-way along a wishbone, on a pushrod-driven rocker or on an inclined strut. When the wheel moves 10 mm, the spring may only compress 7 mm. That ratio is the **motion ratio**:

$$MR = \frac{\Delta x_{spring}}{\Delta z_{wheel}}$$

In this lesson (and in most damper and spring literature) MR is *spring (or damper) travel per unit of wheel travel*, so MR < 1 means the spring moves less than the wheel.

**See it on the jig.** The figure below is a pushrod corner on a test jig: a lift pad moves the wheel, the wishbones swing, the pushrod turns the rocker and the rocker compresses the coil-over. Under the drawing, the *Wheel* and *Spring* bars share one millimetre scale, so MR is simply the ratio of their lengths; the chart plots MR across the whole travel for the four rockers.

**Try it:**
- Pick **Linear · high MR** and drag the wheel to **+50 mm**: the spring moves about **43 mm** (MR ≈ 0.87). Now pick **Linear · low MR**: the same wheel travel moves the spring only **27 mm** (MR ≈ 0.55). Same car, same 180 N/mm spring, but the wheel rate drops from about **136 to 54 N/mm** – that is the "squared" effect explained next.
- Pick **Rising rate** and sweep from −55 to +55 mm: MR climbs from **0.48 to 0.83**, so the wheel rate goes from about **42 to 123 N/mm** – soft in droop, stiff in bump. **Falling rate** does the opposite (0.70 → 0.43).
- Watch the lit rocker: the rising-rate rocker's spring arm starts *past* square to the spring and comes square in bump. The arm **lengths** set the average MR; the arm **angles** set how MR changes with travel.

**Takeaway:** MR is not a single number fixed by the car – it is designed into the rocker. Engineers use a rising rate to hold the aero platform at high load without making the car harsh over small bumps.

**Why it enters squared.** A lever works twice:
1. The spring compresses only $MR$ times the wheel travel, so it generates only $MR$ times the force it would at the wheel.
2. That spring force is then fed back to the wheel through the same lever, so the wheel sees it reduced by $MR$ again.

Hence the **wheel rate**:

$$K_w = k_{spring} \cdot MR^2$$

A 200 N/mm spring on MR 0.7 gives only $200 \times 0.49 = 98$ N/mm at the wheel – half the number painted on the spring. The same squared law applies to damper coefficients: a damper rated 5 N/(mm/s) on MR 0.7 gives about 2.5 N/(mm/s) at the wheel, and the damper shaft only sees 70 % of the wheel velocity.

**Typical numbers**
| Car | Layout | Typical spring/damper MR |
|---|---|---|
| GT3 / GT4 front | coil-over on lower wishbone | ~0.6–0.9 |
| TCR | MacPherson strut | ~0.9–1.0 (strut nearly at wheel) |
| F4 / F3 / F2 | pushrod + rocker | ~0.5–1.0, set by rocker design |
| LMP2 / Hypercar | pushrod/pullrod + rocker, often with heave element | corner and heave ratios differ |

**Installation ratio** is often used as a synonym. Some teams use it to mean MR including the spring inclination angle (the cosine term covered at Level 2). Always check which convention a setup sheet or simulation tool uses before you compare numbers.

The practical point for a new engineer: when you change spring, you change wheel rate by the spring ratio – but when someone changes a rocker, bellcrank or mounting point, the rate changes with the *square* of the geometry change.

## L2 · Practitioner

**Three different motion ratios.** On the same corner, the spring, the damper and the anti-roll bar can each have their own ratio:
- **Spring MR** – spring compression per wheel travel.
- **Damper MR** – damper shaft travel per wheel travel. Identical to the spring MR only if the spring is concentric with the damper (coil-over). On many formula and prototype cars, the damper and spring are separate units on the rocker at different radii.
- **ARB MR** – bar arm (or drop-link) travel per wheel travel, which converts bar torsional stiffness into wheel rate in roll. On single seaters the bar is often driven by the rocker; on GT cars by a drop link from the wishbone or upright.

**Inclination.** If a coil-over is mounted at angle $\theta$ from the direction the mounting point moves, only the component along the spring axis compresses it: $MR_{eff} = MR_{lever} \cdot \cos\theta$. At 10° the error is 1.5 %; at 30° it is 13 % on MR and **25 % on wheel rate**.

**Measuring it on the car (the only number you should trust)**
1. Remove the spring (keep the damper fitted with its gas pressure released if possible, or fit a linear pot in its place) and disconnect the ARB drop links, so the wheel moves freely and the damper length can still be read.
2. Jack the wheel through its travel in 5–10 mm steps, measuring wheel-centre height (or ride-height at the hub) and damper length (calipers, the damper pot, or a dial gauge).
3. Plot damper length against wheel position. The slope is MR; the curvature tells you if it is rising or falling rate.
Do this over the *running* range (static to bump-rubber contact), not just around static.

**Worked example – GT3 front**
- Spring 200 N/mm, lever MR 0.80, coil-over inclined 10° → $MR_{eff} = 0.80 \cdot \cos 10° = 0.788$
- Wheel rate: $200 \times 0.788^2 = 124$ N/mm
- Tyre vertical rate ~350 N/mm in series → ride rate $\frac{124 \cdot 350}{124 + 350} \approx 92$ N/mm
- Corner sprung mass 300 kg → ride frequency $\frac{1}{2\pi}\sqrt{92\,000/300} \approx 2.8$ Hz

**Using it in data.** Damper potentiometers measure damper travel. To get wheel travel you divide by MR (in this convention); to get wheel velocity, divide damper velocity by MR. Segers builds his roll-angle math channels from damper pots in the same way, but he defines MR the other way round ($MR_{Segers}$ = wheel/damper ≈ 1/MR here; his example front value 1.373 corresponds to MR ≈ 0.73 in this lesson), so his equations *multiply* damper travel by MR. When you use his roll-angle equations, substitute 1/MR from this lesson. A factor-of-MR or MR² discrepancy between two engineers' numbers is almost always this convention mix-up.

**Common pitfalls**
- Comparing spring rates between cars without comparing MRs: a Cup car and a GT3 with the "same" springs can have 30 % different wheel rates.
- Forgetting that a rocker change also changes damper MR, so damping ratio changes with it.
- Taking the MR from a CAD sheet at design ride height and running the car 15 mm lower where the rocker is in a different part of its curve.

## L3 · Advanced

**Derivation by virtual work.** Let spring compression $s$ be a function of wheel position $z$. The spring stores $U = \tfrac12 k\, s(z)^2$. The vertical force at the wheel is the derivative of energy with respect to wheel travel, and the wheel rate is the second derivative:

$$F_w = \frac{dU}{dz} = k\, s\, \frac{ds}{dz} = F_s \cdot MR$$
$$K_w = \frac{d^2U}{dz^2} = k\, MR^2 + F_s \frac{dMR}{dz}$$

The first term is the familiar $k\,MR^2$. The second term is the **geometric stiffness** from a motion ratio that changes with travel: it is proportional to the spring *force* (i.e. preload plus static load). On a rising-rate rocker carrying 5 kN of spring force with $dMR/dz = 0.002$ /mm, it adds 10 N/mm – a 5–10 % effect on a GT car, larger on a heavily loaded aero car at speed. Simple "k·MR²" spreadsheets miss it, which is one reason measured wheel rates (K&C rig) differ from calculated ones.

**Damping scales identically.** Damper velocity $\dot s = MR \cdot \dot z$ and force reflects through MR again, so $c_w = c \cdot MR^2$. Rocker changes therefore move the damper's operating point on its curve *and* the effective wheel damping. If a new rocker drops MR from 0.9 to 0.75, wheel damping falls 31 % *and* shaft speeds fall 17 %, so a damper that was in its high-speed region over kerbs may now sit near its knee.

**Heave vs roll ratios.** With a third (heave) element or a Z-bar, define MR per *mode*:
- Heave MR: heave element travel per mm of *both* wheels rising together.
- Roll MR: ARB arm travel per mm of *opposite* wheel motion.
The corner spring sees both modes; the heave spring sees (ideally) only heave; the ARB only roll. Roll stiffness from the corner springs, with $K_w$ per side and track $t$:

$$K_{\phi,springs} = \frac{K_w\, t^2}{2} \quad [\text{N·m/rad}]$$

with $K_w$ in N/m and $t$ in m (e.g. 120 N/mm = 120 000 N/m, $t$ = 1.6 m → 153.6 kN·m/rad ≈ 2.68 kN·m/deg). Wheel rates give the suspension roll stiffness that sets body roll; for the total roll stiffness including tyre deflection use ride rates (tyre in series). MR errors propagate squared into roll stiffness too, and therefore into LLTD.

**Data-derived MR.** With a laser ride-height sensor near the axle and damper pots, a scatter plot of damper travel vs wheel-centre travel (laser minus tyre deflection estimate) on a straight gives a running MR. Deviations from the kinematic value reveal compliance (rocker mounts, pushrod bending) and incorrect sensor calibration.

## L4 · Expert

**Design and trade-off view.** Choosing MR is not free:
- **Low MR** (spring far from wheel motion) needs very stiff, highly loaded springs and dampers for the same wheel rate: forces at the element scale with $1/MR$, travel with $MR$. Shaft speeds are small, so the damper works in its low-speed region where friction, valve hysteresis and gas-force effects are a larger fraction of output. Sensor resolution on the damper pot also suffers.
- **High MR** gives better damper control and resolution but more travel, packaging issues and higher shaft speeds over kerbs (cavitation and heat).

Most modern formula and prototype rockers target damper MR around 0.7–1.0 for this reason.

**Rising/falling rate as a tuning tool.** Rocker progression is a way of getting a soft initial rate for mechanical grip and a rising rate as aero load compresses the car, without relying on bump rubbers. Its cost is that every rate number becomes a function of ride height – and therefore of speed, fuel and tyre growth. The engineer must evaluate wheel rate, damping ratio and roll stiffness *at the dynamic ride height* the car actually runs in each corner, not at the static setup-pad height.

**Model limits.** The $k\,MR^2$ concept assumes a single-degree-of-freedom path from wheel to element. In reality the pushrod, rocker bearings and chassis pick-ups are springs in series with the coil spring. A 0.5 mm deflection of a rocker mount at 8 kN is a 16 kN/mm series stiffness – harmless for a 150 N/mm spring, but for a 400 N/mm heave spring on a hypercar it is already a measurable rate loss and a source of phase lag between wheel and damper, which matters in damper tuning for high-frequency platform control.

## Key formulas

**Motion ratio**

$$MR = \frac{\Delta x_{spring}}{\Delta z_{wheel}} = MR_{lever}\cos\theta$$

- Δx_spring: spring/damper travel (mm)
- Δz_wheel: vertical wheel travel (mm)
- θ: element inclination to its mounting point path

**Wheel rate**

$$K_w = k\, MR^2$$

- k: spring rate (N/mm)
- K_w: wheel rate (N/mm)

**Wheel rate with varying MR**

$$K_w = k\,MR^2 + F_s\,\frac{dMR}{dz}$$

- F_s: spring force (N)
- dMR/dz: MR change per mm of wheel travel

**Wheel damping**

$$c_w = c\, MR^2$$

- c: damper coefficient (N·s/mm)
- c_w: damping at the wheel

**Ride rate (tyre in series)**

$$K_{ride} = \frac{K_w K_t}{K_w + K_t}$$

- K_t: tyre vertical stiffness (N/mm)

## Trackside takeaways

- Wheel rate = spring rate × MR²; damping scales the same way.
- Spring, damper and ARB can each have a different MR – measure them separately.
- Inclination: MR multiplies by cos θ, wheel rate by cos² θ.
- Check the convention (spring/wheel vs wheel/spring) before comparing numbers or building math channels.
- Rising-rate rockers make every rate a function of ride height – evaluate at dynamic ride height.

## By car category

### GT3

Front coil-overs usually act on the lower wishbone near the upright with modest inclination; MR ~0.6–0.9. Spring catalogues are shared across cars, but wheel rates are not – always convert before benchmarking against another manufacturer.

### TCR

MacPherson front: the strut is almost the kingpin, so MR is close to 1 and wheel rate ≈ spring rate. Rear twist-beam or multi-link cars can have very low spring MR at the rear.

### FIA F3

Pushrod-rocker front and rear with spring, damper and ARB all on the rocker. Rocker geometry is spec, so the MR table in the Dallara manual is the reference – but verify on the car after a crash repair.

### Hypercar (LMH/LMDh)

Corner springs, heave (third) elements and roll bars each have their own mode MR. Ride-height-dependent rocker progression is common, so quote rates at the dynamic platform, not at static.

### One-make Cup

Spring choice is often limited to a short list; understanding MR tells you how big a step each option really is at the wheel.

## References

- Milliken & Milliken, Race Car Vehicle Dynamics (SAE 1995): Ch. 16 Ride and Roll Rates (wheel rate, ride rate, installation ratio)
- Milliken & Milliken, Race Car Vehicle Dynamics (SAE 1995): Ch. 21 Suspension Springs
- Segers, Analysis Techniques for Racecar Data Acquisition, 2nd ed. (SAE 2014): §9.1 Measuring Suspension Roll Angle (damper pots converted to wheel motion through MR)
