# Camber gain & camber compensation in roll

> Body roll tilts the outside tyre towards positive camber; suspension geometry gains negative camber in bump to fight it. How much is recovered – and what it costs in heave – shapes static camber choice and tyre temperatures.

Area: Suspension Geometry & Kinematics · Starting level: L1 Foundation · Updated 2026-11-16
Source page: https://race-engineer-academy.vercel.app/lesson/sg-camber-gain

## L1 · Foundation

**The problem.** A tyre makes most lateral force when it sits roughly upright to slightly leaning *into* the corner under load (a race slick typically wants roughly −1° to −2.5° of *dynamic* camber on the loaded outside tyre, depending on construction). When the body rolls by $\phi$, a wheel fixed rigidly to the body would also lean by $\phi$ – towards **positive** camber on the outside wheel, exactly the wrong way.

**Static camber** is the first fix: start the wheel at, say, −3.5°. **Camber gain** is the second: wishbones of unequal length (short upper, long lower) pull the top of the wheel inwards as the wheel rises, adding negative camber in bump.

**Camber gain** is usually quoted as degrees per mm of wheel travel, or degrees of camber change per degree of body roll. For a double wishbone it is set by the **front-view swing-arm length** (distance from the wheel to its instant centre):

$$\frac{d\gamma}{dz} \approx \frac{1}{FVSA}\ \text{rad per unit travel}$$

FVSA 1500 mm → about 0.038 °/mm. 20 mm of bump → ~0.76° more negative.

**Camber compensation** is how much of the body roll the geometry gives back on the outside wheel. With track $t$ the outside wheel rises $\phi\,t/2$ when the body rolls, so:

$$\text{compensation} = \frac{t}{2\,FVSA}$$

Track 1600 mm, FVSA 2000 mm → 40 %. With 1.5° of roll the outside wheel loses only 0.9° relative to the ground instead of 1.5°.

**Typical roll per g:** formula cars ~0.3–0.7 °/g, GT3 ~0.6–1.2 °/g, TCR/GT4 ~1–2 °/g. More roll → more camber the geometry must compensate → more static negative camber needed.

## L2 · Practitioner

**Why not 100 % compensation?** It needs FVSA = t/2, i.e. the front-view IC on the car centreline (the geometry of a centre-pivot swing axle). That gives perfect roll compensation – but in pure heave both wheels gain ≈57.3/(t/2) °/mm (≈0.07 °/mm on a 1600 mm track: 25 mm of aero compression = −1.8° extra on both tyres). The RC height then equals the IC height, so any IC height above ground brings strong jacking. Race geometry is a compromise: aero cars that move 20–30 mm in heave favour long FVSAs (little heave camber change, low compensation) and control roll with stiff springs/bars instead.

**Practical consequence: static camber depends on roll stiffness.** If you soften the ARB and the car rolls 0.3° more at 1.5 g, the outside wheel loses roughly $0.3 \times (1 - \text{compensation})$ ≈ 0.2° of ground camber. That may be enough to move the tyre out of its temperature spread target.

**Reading tyre temperatures for camber** (pyrometer, inner/middle/outer after a run):
- Slicks are commonly run with the inner shoulder ~5–10 °C hotter than the outer at the outside of the dominant corner direction; a much bigger spread suggests too much static negative camber for the roll/camber gain, a reversed spread too little.
- Tyre manufacturers often impose limits (e.g. maximum negative camber in GT series supplied by a single tyre maker). Know them before you chase temps.
- Read with tyre carcass probe, not surface IR, after the in-lap cool-down distortion is understood.

**Measuring camber gain:** camber gauge on the hub face (or digital inclinometer on a flat plate), spring removed, jack wheel through its travel in 10 mm steps. Plot camber vs wheel travel – slope and curvature. Do both sides; asymmetric shimming and bent wishbones show up here.

**Other contributors to dynamic camber (often bigger than people expect):**
- Tyre lateral deflection (carcass roll-over): a few tenths of a degree to over a degree of effective camber.
- **Compliance camber** – uprights, wishbones, bearings deflect under lateral load: ~0.05–0.15 °/kN on GT-type cars. At 6 kN outside-front lateral force that is 0.3–0.9° positive.
- Caster and KPI camber change with steer (see the steering-axis lesson): the outside front gains negative camber with steer through caster.

## L3 · Advanced

**Kinematic derivation.** For a double wishbone, the wheel rotates about its IC in front view. A wheel travel $dz$ rotates the wheel plane by $d\gamma = dz/d_{IC}$ (in radians), with $d_{IC}$ the lateral distance from the contact patch to the IC – identical to the FVSA. Inclination of the line to the IC introduces a small lateral scrub, $dy = dz\, h_{IC}/d_{IC}$, which is the same geometric ratio that sets the RC height.

**Ground camber of the outside wheel in roll** (sign: negative = top in):

$$\gamma_{ground} = \gamma_{static} + \phi\left(1 - \frac{t}{2\,d_{IC}}\right) + \gamma_{compliance} + \gamma_{steer}$$

with $\phi$ positive towards the outside. Non-linearity: on typical SLA geometries the IC moves outboard (towards the wheel) in bump, so $d_{IC}$ shrinks and the camber gain per mm increases with bump – the camber-vs-travel curve steepens (becomes progressively more negative) in bump. A sound design target is a near-linear curve over the working range.

**Inside wheel.** In droop the inside wheel loses negative camber (geometry reverses) *and* the body roll tilts it into negative camber relative to ground. The inside tyre's camber therefore goes strongly negative relative to the ground – but it is lightly loaded, so its contribution is small except in long, low-g corners and on low-roll-stiffness cars like TCR.

**Interaction with heave and aero.** On an aero car, ride height falls with speed. If the geometry gains −0.04 °/mm and the front drops 20 mm from slow to fast corners, both front tyres arrive in fast corners with −0.8° more camber than in slow ones. The camber you choose statically is therefore a **speed-weighted compromise**; check camber at the dynamic ride height of the corners that matter most for lap time.

**Data method.** Estimate dynamic outside-wheel camber as a math channel:
camber_dyn = static + roll(from damper pots)·(1 − comp) + heave travel·gain + Fy·compliance. Compare across corners with the tyre spread data – it is the only trackside way to see why the same camber gives good temps in slow corners and overheated inner shoulders in fast ones.

## Key formulas

**Camber gain**

$$\frac{d\gamma}{dz} \approx \frac{1}{FVSA}\ \text{[rad/mm]}\ = \frac{57.3}{FVSA}\ \text{[deg/mm]}$$

- FVSA: front-view swing-arm length, mm

**Camber compensation in roll**

$$\kappa = \frac{t}{2\,FVSA}$$

- t: track width (mm)
- κ: fraction of body roll recovered at the outside wheel

**Outside-wheel ground camber**

$$\gamma_{gnd} = \gamma_{st} + \phi\,(1-\kappa) + C_\gamma F_y$$

- φ: body roll (deg)
- C_γ: compliance camber (deg/kN)
- F_y: lateral force (kN)

## Trackside takeaways

- Body roll pushes the outside tyre towards positive camber; static camber and camber gain fight it.
- Camber gain ≈ 57.3/FVSA deg per mm; compensation = t/(2·FVSA).
- 100 % roll compensation means huge camber change in heave – aero cars avoid it.
- Softening roll stiffness costs dynamic camber; recheck tyre temps after big ARB changes.
- Compliance camber (0.05–0.15 °/kN) can be as large as the kinematic gain.

## By car category

### GT3

Static front camber typically −3° to −4°, often capped by the tyre supplier's recommendation. GT3 roll gradients around 0.6–1.2 °/g make camber recovery a real factor in ARB choice.

### TCR

MacPherson struts have poor camber gain and roll a lot (1–2 °/g); TCR cars rely heavily on static camber (front often near the regulation/tyre limit) and on caster-induced camber with steering.

### Formula 4

Soft-ish chassis and simple geometry: camber gain is modest and roll gradient is larger than in higher formula classes, so camber temps respond clearly to ARB changes – a great car to learn tyre-temp reading.

### LMP2

Long swing arms to minimise camber change in heave; roll controlled with stiff springs/bars. Camber in fast corners is dominated by ride-height drop and compliance.

### Super Formula

Very stiff platform and high aero loads: the speed-dependent heave camber change outweighs roll compensation. Choose camber for the high-speed corners that matter at Suzuka-type circuits.

## References

- Milliken & Milliken, Race Car Vehicle Dynamics (SAE 1995): Ch. 17 Suspension Geometry (swing-arm length, camber change in roll and bump)
- Milliken & Milliken, Race Car Vehicle Dynamics (SAE 1995): Ch. 2 Tire Behavior (camber thrust and optimal camber)
- Milliken & Milliken, Race Car Vehicle Dynamics (SAE 1995): Ch. 23 Compliances (compliance camber)
