# Bump steer & roll steer

> Toe that changes with wheel travel steers the car without the driver. Measuring it with a bump-steer gauge and shimming the track-rod end is a core workshop skill; using roll steer deliberately is a balance tool.

Area: Suspension Geometry & Kinematics · Starting level: L1 Foundation · Updated 2026-11-16
Source page: https://race-engineer-academy.vercel.app/lesson/sg-bump-steer

## L1 · Foundation

**Bump steer** is toe change as the wheel moves vertically. It happens when the track rod (front) or toe link (rear) does not swing on an arc that matches the wheel's motion: as the upright rises, the track rod pulls or pushes the steering arm and the wheel steers.

**Roll steer** is the same effect expressed per degree of body roll. In roll, the outside wheel goes into bump and the inside into droop, so bump steer on both sides adds up to a steer angle of the *axle*:
- Front outside wheel toes **out** in bump → front axle steers out of the corner → **roll understeer**.
- Rear outside wheel toes **in** in bump → rear axle steers in the same direction as the front wheels, increasing rear slip angle → **roll understeer** (stabilising).
- The opposite signs give roll oversteer.

**Units:** toe change in degrees per mm of travel (or mm of toe per 25 mm of bump, measured over the rim). Good race geometry typically holds front bump steer below ~0.05° over ±25 mm around ride height, unless a deliberate amount is designed in.

**What the driver feels:**
- Front bump steer → car darts over bumps and kerbs, steering wheel kicks, braking instability as the front dives (both wheels toe out/in together).
- Rear bump steer → rear "steers itself" over bumps or under squat: a nervous, rear-steering sensation on exits.

**Why it matters more than its size suggests:** a 0.2° toe change on a rear tyre is a 0.2° change in that tyre's slip angle – with a GT3 rear tyre cornering stiffness of very roughly 1.5–2.5 kN/deg at moderate load (so ~3–5 kN/deg per axle), that is 300–500 N of unwanted lateral force appearing every time the car hits a bump.

## L2 · Practitioner

**Measuring bump steer (workshop procedure)**
1. Car on flat pads at ride height, spring removed (or coil-over replaced by a solid rod so you can move the wheel), ARB disconnected. Steering locked straight ahead with a clamp.
2. Bolt a bump-steer plate to the hub face. Mount a gauge with two dial indicators (or lasers) on a stand that does *not* move with the wheel, reading front and rear edges of the plate.
3. Jack the wheel through its travel in 5 or 10 mm steps from full droop to bump-rubber contact; at each step zero the vertical reading and record front/rear dial difference.
4. Convert: toe (deg) = atan(difference / plate length). Plot toe vs wheel travel.

**Reading the plot**
- **Straight sloped line** → the track rod is at the wrong *angle* (its outer end too high or low relative to the ideal line through the IC). Fix by **shimming the outer track-rod end** (spacers between rod end and steering arm, typically 0.5–1 mm increments) or moving the rack height where possible.
- **Curved (parabolic) line** → the track rod is the wrong *length* (inner pivot not on the line joining the wishbone inner pivots in front view). Fix requires rack spacers/inner pickup changes – not usually trackside.

**Sensitivity rule of thumb.** Raising the outer track-rod end by $\Delta h$ changes the toe slope by roughly

$$\frac{d\delta}{dz} \approx \frac{\Delta h}{l_{tr}\,a}$$

where $l_{tr}$ is the track-rod length and $a$ the steering-arm length. With 350 mm and 120 mm: 1 mm shim ≈ 0.0014 °/mm ≈ 0.034° per 25 mm.

**Trackside reasons to recheck bump steer:**
- Ride-height changes > ~5 mm – the car now operates on a different part of the curve.
- Any front-end damage (bent steering arm, upright, track rod).
- Rack replacement or rack spacer change.
- On GT cars, front toe and caster adjustments made by threads on links can move pickup geometry slightly.

**Using roll steer deliberately:** a small rear toe-in-in-bump is commonly designed into GT and prototype rears for stability at high speed; teams with free geometry also use small front toe-out in bump to calm a nervous front on bumpy tracks. Both trade some response for stability.

## L3 · Advanced

**Contribution to understeer gradient.** Roll steer coefficients $\varepsilon_f$, $\varepsilon_r$ (deg of axle steer per deg of roll, sign positive = steers out of the turn) add to the understeer gradient through the roll gradient $R_\phi = d\phi/da_y$:

$$\Delta K_{us} = (\varepsilon_f - \varepsilon_r)\,R_\phi$$

For the rear, use the same sign convention: $\varepsilon_r$ positive when the rear axle steers out of the turn (toe-out of the outside rear in bump, i.e. towards oversteer). With front roll steer 0.08 °/° out, rear 0.05 °/° toe-in-in-bump (counts as −0.05 in this convention) and $R_\phi$ = 1 °/g: $\Delta K_{us}$ ≈ +0.13 °/g of understeer – comparable to a sizeable ARB change on a GT car whose total understeer gradient may only be 0.5–1.5 °/g.

**Relation to bump steer:** in pure roll the wheel travel is $z = \phi\,t/2$, so the axle roll steer (average of both wheels, for a symmetric linear curve) is $\varepsilon \approx (d\delta/dz)\cdot t/2$ in rad/rad. A curved bump-steer characteristic gives zero roll steer (left and right cancel) but toe change in heave – which is why curvature shows up only as aero-load-dependent toe, while the slope gives both roll steer and heave toe.

**Heave toe on aero cars.** Front axle compressing 20 mm at speed with a parabolic bump-steer of 0.1° at 20 mm means the car runs 0.1° per side more toe-out (or in) at top speed than on the setup pads. On a rear axle this changes high-speed stability; on the front it changes straight-line darting. Dynamic toe = static toe + bump-steer(z) + compliance steer(Fy, Mz).

**Measurement with data.** Symmetric heave on a linear bump-steer curve toes the two wheels equally and oppositely, so the axle steer is zero and there is no yaw: yaw over bumps comes from *asymmetric* travel. On a straight with zero steering-wheel input, plot yaw rate (or measured minus expected lateral acceleration) against front left-minus-right wheel travel (front roll/warp displacement from the damper pots ÷ MR). A consistent slope indicates roll steer / linear bump steer at that axle; repeat with the rear pots for the rear. Note that bump steer is a function of wheel *displacement*, not velocity. Toe change with heave (from both the slope and the curvature of the bump-steer curve) shows up instead as tyre drag and darting that correlate with front heave displacement (e.g. extra speed loss at high aero load), not as yaw.

## Key formulas

**Toe from bump-steer gauge**

$$\delta = \arctan\frac{d_{front} - d_{rear}}{L_{plate}}$$

- d_front, d_rear: dial readings (mm)
- L_plate: distance between dials (mm)

**Shim sensitivity**

$$\frac{d\delta}{dz} \approx \frac{\Delta h}{l_{tr}\,a}\ \text{[rad/mm]}$$

- Δh: shim height change (mm)
- l_tr: track-rod length (mm)
- a: steering-arm length (mm)

**Roll steer from bump steer**

$$\varepsilon \approx \frac{d\delta}{dz}\cdot\frac{t}{2}$$

- ε: roll steer (rad/rad)
- t: track (mm)

**Effect on understeer gradient**

$$\Delta K_{us} = (\varepsilon_f - \varepsilon_r)\,\frac{d\phi}{da_y}$$

- ε_f, ε_r: roll steer, positive = steers out of turn

## Trackside takeaways

- Straight bump-steer line → wrong track-rod angle → shim the outer end.
- Curved line → wrong track-rod length → rack/inner pickup change.
- Outside front toe-out in bump and outside rear toe-in in bump = roll understeer (stabilising).
- Recheck bump steer after ride-height changes over ~5 mm or any front-end contact.
- Dynamic toe = static toe + bump steer + compliance steer.

## By car category

### GT3

Track-rod outer shims are usually allowed and documented in the manual; ride-height changes of more than a few mm warrant a bump-steer check because GT3 racks are positioned for a nominal ride height.

### Formula 4

Spec geometry but home-built shimming errors after crash repairs are common; a bump-steer check is cheap insurance before a race weekend.

### TCR

Road-car derived rack and MacPherson geometry; bump steer is not freely adjustable and roll steer is part of the homologated character. Ride-height changes move you along a curve you cannot fix.

### Hypercar (LMH/LMDh)

Toe link geometry is tightly specified; compliance steer and heave toe at high aero load are of the same order as kinematic bump steer – validate on a K&C rig.

### IndyCar

Oval setups use asymmetric bump steer deliberately; on road courses teams chase near-zero front bump steer around the dynamic ride height.

## References

- Milliken & Milliken, Race Car Vehicle Dynamics (SAE 1995): Ch. 17 Suspension Geometry (bump steer and roll steer)
- Milliken & Milliken, Race Car Vehicle Dynamics (SAE 1995): Ch. 19 Steering Systems (track-rod geometry)
- Milliken & Milliken, Race Car Vehicle Dynamics (SAE 1995): Ch. 5 Simplified Steady-State Stability and Control (roll steer contribution to understeer gradient)
