# Anti-dive, anti-squat & anti-lift

> Side-view geometry can route part of the longitudinal load transfer through the links instead of the springs, controlling pitch. It never changes how much load is transferred – only the path, and therefore pitch, platform and feel.

Area: Suspension Geometry & Kinematics · Starting level: L2 Practitioner · Updated 2026-11-16
Source page: https://race-engineer-academy.vercel.app/lesson/sg-anti-geometry

## L1 · Foundation

**The pitch problem.** Under braking, load transfers from rear to front: $\Delta F_z = m\,a_x\,h/L$. On springs alone the nose dives and the tail lifts. Under acceleration the tail squats. For a downforce car, every millimetre of pitch shifts aero balance and ride height.

**Side-view instant centre (SVIC).** In side view, the wishbones (or their pivot axes) are usually inclined. Extend them: they intersect at the **side-view instant centre**. When a brake or drive force acts at the tyre, part of it is converted by the inclined links into a *vertical* force on the chassis.

- **Anti-dive** – front, braking: the links push the nose up while braking.
- **Anti-lift** – rear, braking (stops the tail lifting); or front, acceleration on a front-driven car.
- **Anti-squat** – rear, acceleration: the links lift the tail under drive.

Expressed as a percentage: 100 % anti-dive means *all* the front load transfer from braking goes through the links – zero dive. 0 % means all through the springs.

**The key misconception:** anti-geometry does **not** reduce load transfer. The front tyres gain exactly $m\,a_x\,h/L$ either way. It only decides whether that load goes through the springs (and makes the car pitch) or through the wishbones (and doesn't).

**Typical values** (wide range, often adjustable by inner pickup shims on GT and prototype cars):
| Car | Front anti-dive | Rear anti-squat |
|---|---|---|
| GT3 | ~10–40 % | ~20–60 % |
| Formula (F3/F2) | ~0–30 % | ~20–50 % |
| Road car | ~10–30 % | ~10–50 % |

## L2 · Practitioner

**Calculating the percentage.** For outboard brakes, the brake force acts at the contact patch. Draw a line from the contact patch to the SVIC; its angle above horizontal is $\theta_f$. With front brake fraction $p_f$:

$$\%AD_f = \tan\theta_f \cdot \frac{L}{h}\cdot p_f \cdot 100$$

For drive forces through half-shafts with an inboard (chassis-mounted) diff, the torque is reacted by the chassis and only the force at the **wheel centre** pushes on the upright – so use the line from wheel centre to SVIC ($\theta_r$ measured from the hub):

$$\%AS_r = \frac{\tan\theta_r}{h/L}\cdot 100$$

Note: **anti-dive depends on brake balance.** Moving brake bias forward increases front anti-dive percentage and decreases rear anti-lift percentage. Inboard brakes (some formula cars historically) use the wheel-centre line instead.

**Example (GT3 front):** wheelbase 2.7 m, CG height 0.45 m (L/h = 6.0), SVIC line from contact patch at 4°: tan 4° = 0.070 → $0.070 \times 6.0 \times 0.62$ (62 % front bias) = 26 % anti-dive. Front dive is reduced by about a quarter.

**Effects the driver and engineer notice**
- **Less pitch** → more stable aero platform under braking; front splitter/floor height better controlled; less rearward aero balance shift on exit if anti-squat holds the rear.
- **Feel:** drivers read weight transfer partly through pitch. High anti-dive makes the car feel "wooden" on the brakes; they can't feel the front loading.
- **Harshness and grip on bumpy braking zones:** load through links is undamped and unsprung; a bump under braking passes more directly to the chassis. Anti-dive also makes the suspension effectively stiffer to longitudinal impacts.
- **Caster change:** with inclined pickup axes, the upright rotates in side view as it moves – caster changes under dive, changing steering weight under braking.
- **Anti-squat > 100 %** lifts the rear on power: can unload the rear tyres' springs, and in combination with the diff can cause axle hop on poor-traction exits.

**Trackside use:** where the manual offers shim packs on inner pickups, anti-squat is a recognised traction/exit-stability tool on GT cars; anti-dive more often a platform tool on prototypes. Make the change, then check pitch gradient (Segers §9.7) to confirm the effect actually happened.

## L3 · Advanced

**Pitch stiffness view.** With anti-features, the spring-path load transfer is $(1-AD)\,\Delta F_z$ at the front and $(1 - AL)\,\Delta F_z$ at the rear. The pitch angle per g:

$$\frac{d\theta}{da_x} = \frac{m\,h}{L^2}\left[\frac{1-AD}{K_f} + \frac{1-AL}{K_r}\right]$$

(with $K_f$, $K_r$ the axle ride rates, both front and rear contributing). This is what Segers' **pitch gradient** measures from damper pots; plotting pitch vs longitudinal g separately for braking and acceleration shows the anti percentages as different slopes, which is why the pitch characteristic is rarely linear.

**Transient behaviour.** Link-path load transfer arrives with the brake force – no spring/damper delay. Spring-path transfer arrives with the pitch motion (time constant set by pitch frequency and damping). High anti-dive therefore makes the *front tyre load* build faster on initial brake application, which can help initial bite but also makes lock-ups more abrupt if the driver hits the pedal hard.

**Non-linearity.** The SVIC moves with suspension travel. As the nose dives, the anti-dive % changes (often reduces), so the car's pitch stiffness is travel-dependent. Similarly, anti-squat varies with ride height and squat, so the effect on rear ride height under full throttle in 2nd gear can differ from 5th gear because of different travel states and aero loads.

**Interaction with aero.** For aero cars the objective is rarely "zero pitch". A controlled amount of dive lowers the front, which on most diffuser cars increases front downforce under braking and shifts aero balance forwards – more rotation on entry, sometimes at the cost of entry stability. Teams design anti-dive to put the platform where the aero map wants it during the brake phase, not simply to minimise pitch.

**Jacking under braking:** anti-dive > 100 % lifts the nose under braking – rare and undesirable. More common pitfall: low rear anti-lift combined with a forward brake bias (small rear brake fraction) lets the rear rise more than expected under braking, and with pro-lift (negative anti-lift) geometry moving the bias rearwards makes it worse – rake increases, the aero balance shifts forwards and the car becomes nervous on entry. Conversely, rear anti-lift above 100 % pulls the rear *down* under braking and can drive the floor/diffuser towards the ground. With outboard rear brakes, rear anti-lift % scales with rear brake fraction: moving bias rearwards increases it, moving it forwards reduces it.

## Key formulas

**Longitudinal load transfer**

$$\Delta F_z = \frac{m\,a_x\,h}{L}$$

- h: CG height (m)
- L: wheelbase (m)

**Front anti-dive (outboard brakes)**

$$\%AD_f = \tan\theta_f\cdot\frac{L}{h}\cdot p_f\cdot 100$$

- θ_f: angle of contact patch → SVIC line
- p_f: front brake force fraction

**Rear anti-squat (inboard diff)**

$$\%AS_r = \tan\theta_r\cdot\frac{L}{h}\cdot 100$$

- θ_r: angle of wheel centre → SVIC line

**Pitch gradient with anti**

$$\frac{d\theta}{da_x} = \frac{m\,h}{L^2}\left[\frac{1-AD}{K_f}+\frac{1-AL}{K_r}\right]$$

- K_f, K_r: axle ride rates (N/m)
- AD, AL: anti fractions (0–1)

## Trackside takeaways

- Anti-geometry changes the path of load transfer, never its magnitude.
- Anti-dive % scales with brake bias; anti-squat uses the wheel-centre line for inboard diffs.
- High anti = less pitch, faster load build-up, but harsher and less feel.
- Anti percentages vary with travel – pitch gradient is rarely linear.
- Verify geometry changes with a pitch-gradient plot from damper pots.

## By car category

### GT3

Many GT3 manuals offer inner-pickup shim options for anti-squat/anti-dive. Anti-squat is a real exit-traction and rear-platform tool on rear-engined and front-engined cars alike.

### Hypercar (LMH/LMDh)

Platform control is king; anti-dive is designed around brake-phase aero map targets. With hybrid front axles (LMH), front drive forces also create front anti-lift effects under deployment.

### TCR

Front-wheel-drive: front anti-lift under acceleration and anti-dive under braking both act on the same axle. Geometry is road-car derived and largely fixed.

### FIA F2

Spec geometry. Anti numbers are given by Dallara; the engineer feels them through brake-bias changes (which alter anti-dive %).

### One-make Cup

Rarely adjustable – but brake bias changes still change effective anti-dive/anti-lift, so expect small pitch and feel differences with bias.

## References

- Milliken & Milliken, Race Car Vehicle Dynamics (SAE 1995): Ch. 17 Suspension Geometry (side-view swing arm, anti-dive, anti-squat, anti-lift)
- Milliken & Milliken, Race Car Vehicle Dynamics (SAE 1995): Ch. 18 Wheel Loads (longitudinal load transfer)
- Segers, Analysis Techniques for Racecar Data Acquisition, 2nd ed. (SAE 2014): §9.7 Pitch Gradient
