# Tyre-driven setup decisions

> Hot pressure targets, temperature-based camber decisions and degradation management turn the tyre from a black box into a setup input. The best setup is the one that keeps all four tyres in their window for the whole stint.

Area: Setup & Driver Feedback · Starting level: L2 Practitioner · Updated 2026-11-16
Source page: https://race-engineer-academy.vercel.app/lesson/setup-tyre-driven

## L1 · Foundation

The tyre works in a **window**: a range of temperature and pressure where it produces peak grip. Outside the window it slides more, wears faster and the balance changes.

**Pressure targets.** Tyre suppliers and teams specify a **hot** pressure target (e.g. ~1.8–2.0 bar for many GT3 slicks; minimum starting pressures are mandated in some series). You set **cold** pressures so that after 2–4 laps the hot pressure reaches the target. Pressure rises with gas temperature – roughly **0.1 bar per 10 °C**. If the target is missed, adjust the cold pressure for the next run.

**Temperature profile.** A pyrometer (probe) measures inner, middle and outer tread temperature after a run; IR sensors on the car measure it live. Read it like this:
- **Middle hotter** than the average of the edges → pressure too high (crowned contact patch).
- **Middle cooler** → pressure too low.
- **Inside much hotter than outside** → too much negative camber (or too much toe).
- **Outside hotter than inside** → too little negative camber.

A typical cambered race tyre runs the inside a few degrees to ~10 °C hotter than the outside after a representative run.

**Degradation.** Grip falls over a stint through wear and heat cycles and, mostly, through **overheating** the surface. The axle that overheats first drives the balance: if the rears overheat the car becomes loose late in the stint. Setup can reduce the energy put into the critical axle.

## L2 · Practitioner

**Getting the pressure right**
- Use **TPMS** (pressure + gas temperature) where fitted: it shows the warm-up curve and stabilised hot pressure per lap, not just one pit-lane reading. Segers (§8.2 Working with Tire Pressure Monitoring Systems) uses TPMS run charts to show how many laps the pressures need to stabilise – which is why balance judgements made after three laps are unreliable – and back-calculates the cold pressure from the hot reading with the ideal gas law.
- Correct cold pressure by the error: if the target is 1.90 bar hot and you reached 2.02 bar, drop the cold pressure by ~0.10–0.12 bar (the rise is roughly proportional to absolute pressure).
- Watch **blanket temperatures** and ambient: a cold-pressure setting is only valid with the same blanket temperature and similar track temperature.
- **Front/rear and left/right** differences: tracks with more right-hand corners load the left side tyres more; set side-specific cold pressures to land all four on target.

**Camber from temperatures (with caveats)**
- Probe readings after the in-lap reflect the in-lap, not the qualifying lap. Prefer IR sensor data in the relevant corners, or have the driver push until the pit entry.
- Typical targets: inside–outside spread ~5–10 °C; middle within a few degrees of the edge average.
- If spread is too large, reduce negative camber 0.25–0.5° (also check toe – toe-out heats the insides). If too small (outside hot), add camber.
- Optimum camber is ultimately a **lap-time / grip** decision, not a temperature-symmetry decision; the outside tyre in a corner wants more negative camber than the static reading suggests because of roll and tyre deflection.

**Degradation management**
- Identify the limiting axle with a run chart of balance (average understeer angle per lap) and lap time over a long run, corrected for fuel.
- Front-limited: protect the front with less entry rotation demand, a bit less front toe-out, less front camber if wear is on the inside.
- Rear-limited: more rear stability (rear toe-in +0.5 mm, softer rear ARB, more diff locking to reduce inside spin, smoother throttle map, TC higher), start the stint with a bit more understeer.
- Thermal vs mechanical deg: if lap times recover after a cool-down lap, deg is thermal (manage energy). If not, it's wear (manage sliding).

## L3 · Advanced

**Physics of the pressure target.** Pressure sets carcass stiffness and contact patch shape: lower pressure → longer, more compliant patch, higher cornering stiffness at low load but more sidewall flex, heat generation and a peak at higher slip angle; higher pressure → crisper response, smaller patch, lower peak grip and earlier fall-off. Suppliers set a window that balances grip and structural safety (bead/sidewall). Within it, the lap-time optimum is usually narrow (±0.05 bar). Apply the metric-vs-lap-time method (Segers §17.2, Fig. 17.4) to tyre pressure: plot fuel-corrected lap time or grip factor against hot pressure across runs and look for the optimum rather than trusting a single number.

**Gas law correction.** At constant volume, $p_{abs} \propto T$. From cold $(p_c, T_c)$ to hot $T_h$: $p_h = (p_c + p_{atm}) T_h / T_c - p_{atm}$ with temperatures in kelvin. E.g. 1.40 bar gauge at 20 °C reaching 75 °C gas temperature: $(2.413)(348.15/293.15) - 1.013 \approx 1.85$ bar. Volume growth of the tyre at speed slightly lowers the real rise. Nitrogen or dry air reduces moisture-induced scatter.

**Camber and temperature – what the probe can and cannot tell.** The tread temperature distribution integrates the whole lap: straights (camber gives inside heating with no benefit), braking and both corner directions. The outside tyre in a long corner may want more negative camber than temperatures suggest. A better method: IR sensor arrays gated on lateral g (outside tyre, $|a_y| > 1$ g) to read the cornering temperature profile; or test camber directly on lap time with fixed pressures.

**Degradation decisions.** Fit a model of lap time $t(n) = t_0 + d\,n + f\,m_{fuel}(n)$ to long runs to separate tyre deg $d$ from fuel effect. Compare setups on $d$, not just on $t_0$: a setup 0.10 s faster on lap 1 but losing an extra 0.02 s each lap is slower over a 30-lap stint: its average deg penalty is $0.02 \times 29/2 \approx 0.29$ s/lap against a 0.10 s/lap head start, a net loss of ≈0.19 s/lap (≈5.7 s over the stint). It leads on cumulative time only for the first ~11 laps – a qualifying or sprint answer, not a stint answer. Track the per-tyre energy (sliding power $F \cdot v_{slip}$) in simulation or approximate with lateral g and understeer angle metrics.

## Key formulas

**Hot pressure from cold (constant volume)**

$$p_h = (p_c + p_{atm})\,\frac{T_h}{T_c} - p_{atm}$$

- p_h: hot gauge pressure (bar)
- p_c: cold gauge pressure (bar)
- p_atm: atmospheric pressure ≈ 1.013 bar
- T_h: hot gas temperature (K)
- T_c: cold gas temperature (K)

## Trackside takeaways

- Set cold pressures to hit the hot target; ~0.1 bar per 10 °C gas temperature.
- Middle hotter than edges → pressure too high; much hotter inside → too much camber (or toe-out).
- Prefer live IR/TPMS data gated on cornering over pit-lane probe readings.
- Identify the limiting axle over a stint; set up to protect it.
- Compare setups on degradation rate, not only on fastest lap.
- Re-target pressures after any camber change.

## By car category

### GT3

Single-make tyre (Pirelli in SRO, Michelin/Goodyear elsewhere) with specified hot windows and sometimes minimum cold pressures; TPMS mandatory in many championships.

### FIA F2

Pirelli sets minimum starting pressures and camber limits; engineers work within them – pressure is often at the minimum and camber at the limit, so balance comes from other tools.

### Hypercar (LMH/LMDh)

Michelin allocation is limited per event; double- and triple-stinting tyres makes degradation and warm-up (cold pressure choice) a strategic decision.

### TCR

Front tyres do all the work (drive + steer + most braking): front deg and front temperature management dominate setup.

## References

- Milliken & Milliken, Race Car Vehicle Dynamics (SAE 1995): Ch. 2 Tire Behavior
- Milliken & Milliken, Race Car Vehicle Dynamics (SAE 1995): Ch. 12 Chassis Set-up (tyre temperatures and pressure)
- Segers, Analysis Techniques for Racecar Data Acquisition, 2nd ed. (SAE 2014): §8.2 Working with Tire Pressure Monitoring Systems
- Segers, Analysis Techniques for Racecar Data Acquisition, 2nd ed. (SAE 2014): §7.5 The Understeer Angle (run chart of balance over a race)
