# Setup for track characteristics

> Every circuit pulls the setup in a different direction: bumps want compliance, high-speed tracks want platform and low drag, street circuits want ride height, steering lock and stability, kerb-heavy tracks want controlled high-speed damping, and temperature shifts the tyre window. Start the weekend from the right baseline.

Area: Setup & Driver Feedback · Starting level: L2 Practitioner · Updated 2026-11-16
Source page: https://race-engineer-academy.vercel.app/lesson/setup-track-characteristics

## L1 · Foundation

Before arriving at a circuit, classify it. The main characteristics and their usual setup direction:

| Characteristic | Examples | Setup direction |
|---|---|---|
| **Bumpy** | Sebring, Long Beach, old airfields | Softer springs and high-speed damping, higher ride height, softer bump rubbers |
| **High-speed / low-drag** | Monza, Le Mans, Spa (sector 1/3) | Less wing, stiffer platform (heave), lower ride heights, longer gearing |
| **Street circuit** | Macau, Pau, Long Beach, Baku | Higher ride height, more steering lock/Ackermann for hairpins, more downforce, stability under braking, brake cooling |
| **Kerb-heavy** | Zandvoort, Red Bull Ring, Monza chicanes | Compliant high-speed bump, ride height margin, strong suspension parts, kerb-friendly diff/TC |
| **Hot track** | Summer races, Bahrain day | Lower cold pressures, more cooling, guard rear tyres (oversteer tendency), possibly harder compound |
| **Cold / green track** | Early-season, morning sessions | Higher cold pressures, more aggressive warm-up, softer car for mechanical grip |

The goal is not to find a universal "best" setup but to give the driver a car that is **compliant enough** to keep the tyres on the road, **stable enough** to commit, and **efficient enough** (drag vs downforce) for the track's mix of corners and straights.

A practical tool: the **corner speed histogram** of the circuit (time spent per speed band). A track with most cornering time below 120 km/h is a mechanical-grip track; one with most time above 180 km/h is an aero track. This tells you where to put development effort.

## L2 · Practitioner

Practical decisions per track type:

**Bumpy tracks.** Grip comes from keeping the tyre load variation low. Soften springs 10–20%, soften high-speed bump (and sometimes high-speed rebound) 2–4 clicks, raise ride height 2–5 mm to avoid bottoming and plank wear, increase bump-rubber gaps. Accept some aero loss: a car that bottoms or skips loses more than it gains from 3 mm lower ride height. Data check: damper velocity histograms – wider high-speed tails than baseline mean the track is exciting the wheel; ride-height minima at the bumps vs splitter/skid limits.

**High-speed tracks.** Low drag: reduce rear wing (and front to keep balance). Platform matters more because downforce loads are larger: stiffer heave/third springs or packers to control ride height at 250–300 km/h; check bottoming at the end of straights and in compressions (Eau Rouge, Raidillon). Gear ratios: top gear at the limiter just before the braking point of the longest straight, with tow margin.

**Street circuits.** Bumps, crowns, manhole covers, low grip that evolves quickly, walls punishing mistakes. Raise ride heights 3–8 mm vs a permanent circuit; soften; increase steering lock (Macau's Melco hairpin, Monaco's Fairmont, ex-Loews, hairpin) – check lock-to-lock and Ackermann; brake cooling up (repeated heavy stops); more rear stability on entry (driver confidence near walls is worth more than ultimate rotation). Expect track evolution of several seconds per lap over the weekend – don't over-react to Friday balance.

**Kerbs.** Decide which kerbs the driver must use. Soften high-speed bump (blow-off) so the wheel climbs without launching the chassis; enough ride height and packer gap so the car does not ground; a slightly softer rear ARB helps the car ride over an inside kerb on exit. TC/diff that tolerate an unloaded wheel.

**Temperature.** Track temperature changes of 10–20 °C between sessions raise the tyres' gas temperature by part of that amount (measure it with TPMS), typically moving hot pressures by ~0.05–0.15 bar, and change the tyre's grip window. Hotter → reduce cold starting pressures, more cooling for brakes and engine, and expect more rear degradation (oversteer late in a stint) on rear-limited cars.

## L3 · Advanced

**Quantifying the track.** Use previous data or a lap sim to compute: (a) the fraction of lap time in speed bands (mechanical vs aero sensitivity); (b) time at full throttle (drag/power sensitivity – Segers' full-throttle-per-lap metric); (c) lateral g histogram (where grip matters); (d) road roughness from damper velocity histograms or ride-height PSD (Segers Ch. 11–12). Lap-time sensitivity to $C_L A$ vs $C_D A$ ($\partial t / \partial C_L A$ and $\partial t / \partial C_D A$) sets the wing level: on Monza a GT3 may lose more from 1% drag than it gains from 1% downforce; at Hungaroring the opposite.

**Bumpy vs smooth – the compliance trade.** The vertical tyre load variation $\Delta F_z$ (standard deviation) reduces average grip because of load sensitivity: the tyre loses more grip on the unloading half-cycle than it gains on the loading half. Compliance reduces the variance, aero platform demands stiffness. The optimum moves with roughness: the classic two-mode trade (body mode ~2–5 Hz controlled by springs/LS damping; wheel-hop mode ~12–20 Hz controlled by HS damping and tyre stiffness). On bumpy tracks race cars are often damped harder at high shaft speed than the grip optimum: on sharp inputs the damper force ($c\,v$ at 300–500 mm/s) passes straight into the tyre and the chassis. Reducing HS damping lowers these force spikes and the tyre-load variance – provided the wheel-hop mode stays controlled. Too little damping lets the wheel hop (lower unsprung damping ratio, higher resonant peak) and $\sigma_{F_z}$ rises again: there is an optimum, and you accept more body motion to get near it.

**Street-circuit evolution.** Grip may go from $\mu \approx 1.2$ to 1.5 over a weekend on slicks. Balance usually moves toward oversteer as grip rises (more rear-limited because of higher lateral and longitudinal demand on rear tyres and higher temperatures). Build a baseline with a margin of understeer early, and plan bar changes as the track rubbers in.

**Kerb strikes as load cases.** A kerb produces an impulse at the wheel; high-speed damping force at 300–500 mm/s determines how much is transmitted to the chassis. Too stiff → chassis launched, landing on bump stops, snap; too soft → wheel travels into bump rubber anyway. Look at damper position and velocity during kerb strikes and at the time to settle.

**Temperature and tyre window.** For a given compound, the grip vs temperature curve has a plateau; hotter ambient shifts the operating point up. The setup response: reduce energy into the overheating axle (less sliding: balance, toe, camber), lower cold pressures to hit the same hot target, use harder compound if allowed. Cold conditions: the opposite plus warm-up management (more aggressive out-lap, higher blanket temps where permitted).

## Trackside takeaways

- Classify the track: bumpy, high-speed, street, kerb-heavy, temperature – each pulls setup differently.
- Bumpy: soften springs and HS damping, raise ride height; compliance beats a lower but unstable platform.
- High-speed: low drag, firm platform, gearing to the longest straight with tow margin.
- Street: ride height, steering lock, stability, brake cooling; expect large track evolution.
- Kerbs: soft HS bump, ride-height margin, tolerant diff/TC.
- Hot track: lower cold pressures, protect the rear axle, more cooling.

## By car category

### GT3

BoP often sets ride-height and wing ranges per track; Le Mans/Monza use low-drag wing positions. Check homologated options early.

### LMP2

ORECA 07 has a separate low-downforce Le Mans kit; the rest of the season uses the high-downforce configuration.

### FIA F3

Street events (Macau for regional/F3-type cars, Monaco for F2/F3) need increased steering lock and higher ride heights; parc fermé limits late changes.

### IndyCar

Separate road-course, street and oval configurations (aero kits and suspension). Street tracks run higher ride heights and softer setups than permanent road courses.

## References

- Milliken & Milliken, Race Car Vehicle Dynamics (SAE 1995): Ch. 12 Chassis Set-up
- Segers, Analysis Techniques for Racecar Data Acquisition, 2nd ed. (SAE 2014): §17.3 How to Create Metrics (full throttle per lap and other track metrics)
- Segers, Analysis Techniques for Racecar Data Acquisition, 2nd ed. (SAE 2014): §11.4 The Shock Speed Histogram (track roughness from damper velocity distribution)
- Segers, Analysis Techniques for Racecar Data Acquisition, 2nd ed. (SAE 2014): §12.4 Suspension Optimization Using Frequency Analysis
