# Corner phases and which tools act in each

> A corner is a sequence – braking, entry, mid/apex, exit – and each phase has a different load state and therefore a different set of effective setup tools. Matching the tool to the phase is the core skill of setup work.

Area: Setup & Driver Feedback · Starting level: L1 Foundation · Updated 2026-11-16
Source page: https://race-engineer-academy.vercel.app/lesson/setup-corner-phases

## L1 · Foundation

Every corner can be split into four phases, each with a distinct load state:

1. **Braking** (straight line): high longitudinal deceleration (1.2–2.0 g for GT3, 2.5–4+ g for high-downforce formula cars at speed), load transferred to the front, rear unloaded.
2. **Entry / turn-in**: the driver releases the brake progressively while adding steering (**trail braking**). Combined longitudinal and lateral load; the car must start to yaw.
3. **Mid-corner / apex**: close to steady state – peak lateral g, little longitudinal acceleration, minimum speed. Balance here is set mainly by roll stiffness distribution and aero balance.
4. **Exit / traction**: throttle applied, load transfers rearwards, the driven rear tyres must deliver both lateral and longitudinal force.

Why this matters: a setup tool only changes balance in the phases where it is "active". Brake bias does nothing at a constant-throttle apex. The power side of the diff does nothing on the brakes. Anti-roll bars act whenever there is roll – entry, mid and exit – but most strongly mid-corner. So when a driver says "understeer", the first question is **which phase**, because that decides which tool to use.

A simple rule: the **front end** controls entry and mid-corner response; the **rear end** controls stability on entry and traction on exit. Changes that give more front grip in one phase usually reduce rear stability in another. You are always moving the problem around the corner unless you choose a tool that acts mainly in the phase you want.

## L2 · Practitioner

The working tool for an engineer is a **tool × phase matrix**. The table below is a practical guide for a rear-drive downforce car (GT3 / prototype / formula). "High" means the tool is a primary lever in that phase; "Low" means a secondary effect; "–" means essentially no effect.

| Tool | Braking | Entry (trail brake) | Mid / apex | Exit (traction) |
|---|---|---|---|---|
| Brake bias | **High** | **High** | – | – |
| Engine braking map / diff coast lock & preload | Med | **High** | Low | – |
| Diff power ramp / plates | – | – | Low | **High** |
| TC level & throttle map | – | – | Low | **High** |
| Front ARB | Low | Med | **High** | Med |
| Rear ARB | Low | Med | **High** | **High** |
| Corner springs | Med | Med | **High** | Med |
| Heave / third springs, packers | **High** (front pitch) | Med | Med (high speed) | Med (rear squat) |
| LS dampers bump / rebound | Med | **High** | Low | **High** |
| HS dampers | Med (bumps) | Med (kerbs) | Med (kerbs) | Med (kerbs) |
| Front wing / aero balance | Med (high speed) | Med | **High** (high speed) | Med |
| Rear wing / Gurney | Med (stability) | Med | **High** (high speed) | **High** (high speed) |
| Ride height / rake | Med | Med | **High** (aero) | Med |
| Front toe | Low | **High** (response) | Low | Low |
| Rear toe | Med (stability) | Med | Med | **High** (stability) |
| Camber | Low | Med | **High** | Med |
| Tyre pressures | Med | Med | **High** | Med |

How to use it: once the complaint is located ("exit oversteer in slow corners"), read across the row for that phase, pick the tools rated High, then prefer the one with the **fewest side effects in the other phases**. For slow-corner exit oversteer: diff power side, TC/throttle map, rear ARB and rear LS bump/front rebound are candidates; aero is not (speed too low). Softening the rear ARB also touches entry and mid-corner, so the diff or TC may be the cleaner first step if they are free.

In the data, gate your metrics by phase. Segers' cornering sequence (braking point → turn-in → apex → full throttle) maps directly onto brake pressure, steering and throttle channels: e.g. compute average understeer angle only where brake pressure > threshold and steering > threshold to get an "entry balance" metric.

## L3 · Advanced

The matrix is a summary of *why* each tool matters per phase; understanding the mechanism lets you handle cases the table doesn't cover.

**Braking.** Load transfer $\Delta F_z = m a_x h / L$ moves load forward; the brake bias must match the instantaneous front/rear load split including aero load and the pitch-altered aero balance. Heave/pitch stiffness controls front ride height and therefore aero balance in the braking zone – on a rake-sensitive car the centre of pressure moves forward as the nose drops, making high-speed braking nervous.

**Entry.** The car must build yaw while decelerating. Entry balance depends on (a) the rear's longitudinal load (brake bias, engine braking, diff coast lock), (b) the **rate** of lateral load transfer front vs rear – set by low-speed roll damping as much as by springs/ARBs, because the car is in a roll transient – and (c) front response (toe, Ackermann, front pressures). A stiff front low-speed bump and soft rear rebound make the front transfer load faster than the rear: transient understeer. The reverse frees rotation but can make the rear nervous.

**Mid-corner.** Close to steady state, so the **lateral load transfer distribution** (from roll stiffness and roll-centre heights) and **aero balance** dominate, along with camber and pressures (each tyre's peak $\mu$). Dampers have little effect when roll velocity is near zero – which is why damper changes rarely fix a pure apex balance problem.

**Exit.** Longitudinal load moves rearwards ($\Delta F_z = m a_x h / L$ again, smaller magnitude than braking), the rear tyres must share their friction ellipse between drive and lateral force, and the diff decides how drive torque is split between the inside and outside wheels. A more locked diff produces a yaw moment that **resists** rotation at low slip (exit understeer) but can let go suddenly when the inside wheel is overpowered. Rear ARB stiffness increases rear LLTD and unloads the inside rear – more wheelspin.

**Interactions.** The phases are coupled through the driver: if entry is poor, the driver delays throttle, so an exit "fix" might really be an entry fix. Also, tools act in more than one phase: the rear ARB affects entry stability, mid-corner balance *and* traction. The skill is choosing tools whose secondary effects are harmless or beneficial for your specific track.

## L4 · Expert

At expert level, think of the corner as a trajectory through the **g-g-V space** and of each tool as a deformation of the car's yaw-moment capability over that trajectory. Phase is just a convenient partition of $(a_x, a_y, V)$, plus the **rates** $(\dot a_x, \dot a_y)$ that set transient load transfer.

Some consequences that the simple matrix hides:

- **Combined slip decides entry and exit.** On trail braking the front tyres operate on their friction ellipse with significant longitudinal slip; a forward brake bias costs front lateral capacity exactly where the driver needs yaw. The yaw moment available at a given $(a_x, a_y)$ is a function of bias, not only of "front grip". Moment-method (RCVD Ch. 8) plots of $C_N$ vs $a_y$ at constant $a_x$ show this directly.
- **Damper effects scale with rate, not level.** Two drivers with different steering rates experience different damper-induced balance. A setup that suits a driver who turns in at 400 deg/s on the wheel may be lazy for one at 200 deg/s. Gate damper metrics on roll velocity, not just on phase.
- **Aero varies within a phase.** In a fast corner the car may go from 250 to 180 km/h between braking and apex; downforce drops by ~50% ($\propto V^2$), and ride heights rise, shifting aero balance. A corner can be "aero" at entry and "mechanical" at apex.
- **Non-linear elements create phase-dependent tools.** Packers and bump stops act only above a certain load: a front packer gap set to engage under braking makes the front heave stiffness phase-dependent – stiff in braking, soft at the apex. Similarly, diff ramps make locking torque proportional to input torque, so a diff is a different tool at 20% throttle than at 100%.
- **Tyre thermal state shifts with phase usage.** Heavy entry rotation (sliding the rear) heats the rear tyres and moves the late-stint balance towards exit oversteer.

Use of the matrix at this level is therefore quantitative: sensitivity maps (lap-sim or DIL derived) of yaw-moment margin by phase per click of each tool, validated with gated metrics from the logger.

## Key formulas

**Longitudinal load transfer**

$$\Delta F_z = \frac{m\,a_x\,h}{L}$$

- m: vehicle mass (kg)
- a_x: longitudinal acceleration (m/s²)
- h: CG height (m)
- L: wheelbase (m)

## Trackside takeaways

- Always locate a complaint by phase: braking, entry, mid/apex, exit.
- Brake bias, engine braking and diff coast act only off-throttle; diff power and TC act only on-throttle.
- Mid-corner (steady state) balance = roll stiffness distribution + aero balance + tyre peak grip; dampers matter little there.
- Dampers shape the transitions (entry and exit) through the rate of load transfer.
- Prefer the tool with the fewest side effects in other phases.
- Gate data metrics by phase (brake/steer/throttle thresholds) to measure balance per phase.

## By car category

### GT3

ABS and TC are part of the toolset: ABS map changes the entry phase, TC map the exit. Use them before mechanical changes when the problem is phase-specific.

### One-make Cup

Porsche Cup cars have no TC/ABS adjustability in some series and a fixed diff – entry and exit tools reduce to ARBs, brake bias and driving technique.

### FIA F2

Large downforce means aero balance dominates mid-corner of fast turns; in slow corners the mechanical platform and diff (adjustable preload/ramp) do the work.

### TCR

Front-wheel drive flips the exit picture: exit understeer from front tyres doing both drive and steering; rear ARB / rear toe-out help rotation on entry and mid-corner.

## References

- Milliken & Milliken, Race Car Vehicle Dynamics (SAE 1995): Ch. 12 Chassis Set-up
- Milliken & Milliken, Race Car Vehicle Dynamics (SAE 1995): Ch. 8 Force-Moment Analysis (yaw-moment capability vs lateral acceleration)
- Segers, Analysis Techniques for Racecar Data Acquisition, 2nd ed. (SAE 2014): §7.1 The Cornering Sequence
- Segers, Analysis Techniques for Racecar Data Acquisition, 2nd ed. (SAE 2014): §7.4 Driver Activities That Indicate Vehicle Balance
