# Balance of Performance: restrictors, boost, power & energy limits, weight

> BoP equalises different cars with restrictors, boost tables, power caps, energy per stint and minimum weight. Each lever changes a different part of the performance envelope — and therefore which setup and strategy decisions are optimal.

Area: Engine & Hybrid · Starting level: L2 Practitioner · Updated 2026-11-16
Source page: https://race-engineer-academy.vercel.app/lesson/engine-bop-power-limits

## L1 · Foundation

In GT3, GT4, TCR and the WEC/IMSA prototype classes very different cars race together. **Balance of Performance (BoP)** adjusts each model so lap times converge. The main levers:

| Lever | Typical use | What it changes |
|---|---|---|
| **Air restrictor** diameter | NA GT3/LMP | caps air mass flow → caps peak power, flattens the top of the power curve |
| **Boost pressure** table vs rpm | turbo GT3/TCR | sets torque/power curve directly |
| **Power cap / power-speed curve** | Hypercar | maximum total powertrain power, sometimes different above/below a speed |
| **Energy per stint** | WEC Hypercar, LMGT3 | maximum energy usable between refuels (MJ) |
| **Minimum weight / ballast** | everywhere | mass; often with prescribed ballast position |
| **Fuel tank capacity / refuel time** | endurance | stint length, pit time |
| **Ride height, wing range** | some GT series | aero performance |

A restrictor works because once the airflow through the throat reaches the speed of sound (**choked flow**), mass flow cannot increase however hard the engine pulls. Since power ∝ air mass flow, max power ∝ throat area ∝ $d^2$: on a 30 mm restrictor, +0.5 mm is about **+3.4 %** peak power.

For the engineer BoP is a **boundary condition**, not something to argue about at the track. When BoP changes, many optimal choices change with it: wing level, gearing, shift points, ballast placement, brake balance, fuel strategy. Knowing which lever moved tells you what to re-optimise.

## L2 · Practitioner

**How each lever changes your decisions.**

**Less power (restrictor/boost/cap):**
- The car becomes power-limited at lower speed; drag now costs relatively more lap time → re-evaluate **wing angle** (less downforce may now be faster on long-straight tracks — check with lap sim sensitivity, not intuition).
- **Shift points**: a restrictor flattens the power curve above choke rpm $n_c$, so upshifting earlier can cost nothing — but only as long as the rpm *after* the shift stays on the plateau, i.e. $n_{shift} \ge n_c \times$ (gear step). Shift earlier than that and the engine drops below the plateau and loses drive force (see the shifting lesson). Turbo boost tables shape torque over rpm — re-derive optimum shift points from the new curve.
- **Gearing**: with fixed homologated ratios you cannot follow, so the top-gear rpm at end of straight changes; check limiter hits in tow.

**More weight (ballast):**
- Lap time grows roughly as 0.1–0.3 × the relative mass change: on a 2-minute lap with a 1300 kg GT3, +30 kg (+2.3 %) costs ≈ 0.3–0.8 s before tyre effects. Treat this as an order of magnitude and get the exact sensitivity from your lap sim — it is track-dependent (stop-and-go tracks are more mass-sensitive).
- Ballast location is often prescribed (passenger floor), but if it is free, place it low and where it corrects the weight distribution you want.
- Springs/dampers: +40 kg on a 1300 kg car is +3 % mass — ride frequencies drop by ~1.5 %; usually no change needed, but brake balance and tyre temperatures move slightly.

**Energy per stint (WEC):**
- The car must not exceed X MJ between refuels. Energy is spent at full throttle; the engineer converts it into a **per-lap energy target** and coaches lift-and-coast or chooses maps to hit it.
- It makes **efficiency** a performance parameter: lower drag reduces energy per lap at the same lap time; that is why low-drag setups often win in energy-limited races even if single-lap pace is lower.

**Turbo cars and ambient:** cars whose ECU controls charge mass or torque hold power with altitude and temperature by raising boost (until the compressor/turbo-speed limit); restrictor cars lose power as $p_0/\sqrt{T_0}$ falls. Even a turbo car loses a little on a hot day: with a fixed *pressure* target the charge temperature after the intercooler rises with ambient, charge density falls and knock margin shrinks (ignition retard). BoP often includes ambient corrections; check which ones apply to your car.

**Pitfalls:** don't compare "your" power with competitor data from a different BoP version or event; most series publish BoP per event — archive it with the setup sheet.

## L3 · Advanced

**Choked-flow physics.** For isentropic flow of a perfect gas through a throat of area $A$ with upstream stagnation pressure $p_0$ and temperature $T_0$, once the throat Mach number reaches 1:

$$\dot m_{max} = C_d A\, \frac{p_0}{\sqrt{T_0}}\, \sqrt{\frac{\gamma}{R}} \left(\frac{2}{\gamma+1}\right)^{\frac{\gamma+1}{2(\gamma-1)}}$$

For air ($\gamma = 1.4$, $R = 287$ J/kg·K) at 1.013 bar, 25 °C, a 30 mm throat with $C_d \approx 0.95$ passes ≈ 0.16 kg/s. At λ ≈ 0.9 (AFR ≈ 13.2) and ≈ 35 % brake efficiency this supports roughly 180–190 kW — two such restrictors for a typical V8 GT3 is consistent with ≈ 370 kW.

Consequences:
- **Power ∝ $d^2$, ∝ $p_0$, ∝ $1/\sqrt{T_0}$.** Restricted engines lose power with altitude and heat; a hot day (+20 °C) costs ≈ 3 %.
- Above the rpm at which the restrictor chokes, the engine cannot breathe more air: **power becomes flat with rpm, torque falls as 1/n**. The earliest no-loss upshift is $n_c \times$ (gear step), so that post-shift rpm stays on the plateau; revs above that buy nothing but wear and fuel, revs below it cost drive force.
- Engine developers then chase efficiency (thermal and volumetric) — which is why BoP authorities also monitor torque sensors.

**Power caps and torque sensors (Hypercar).** Rather than restrict air, the regulations cap delivered power measured by FIA torque sensors on the driveshafts, and specify a **power-speed curve** — BoP can change the power above a speed (e.g. 250 km/h) separately. This allows the authority to tune straight-line speed independently of acceleration. Engineering consequence: with a hard power cap, the total drive force at speed is fixed; lap time comes from drag, cornering and traction — exactly the opposite of an unrestricted formula car where power is the dominant variable.

**Energy per stint vs fuel tank.** Energy-limited racing is an optimisation with a budget: minimise $\sum t_i$ subject to $\sum E_i \le E_{stint}$. The marginal cost $\partial t/\partial E$ (seconds per MJ) must be **equal at all places on the lap** at the optimum — that is the formal reason lift-and-coast belongs at the end of the longest, fastest straights, where the time cost per MJ saved is smallest.

## Key formulas

**Choked mass flow through a restrictor**

$$\dot m_{max} = C_d A \frac{p_0}{\sqrt{T_0}} \sqrt{\frac{\gamma}{R}} \left(\frac{2}{\gamma+1}\right)^{\frac{\gamma+1}{2(\gamma-1)}}$$


**Restrictor diameter scaling**

$$\frac{P_2}{P_1} \approx \left(\frac{d_2}{d_1}\right)^2$$


**Power from air mass flow**

$$P \approx \dot m_{air} \frac{LHV}{AFR}\, \eta_{th}$$

- LHV: fuel lower heating value (≈ 43 MJ/kg)
- AFR: air–fuel ratio (≈ 13–14.7)
- \eta_{th}: brake thermal efficiency (≈ 0.33–0.45)

## Trackside takeaways

- Restrictor power ∝ d²: +0.5 mm on 30 mm ≈ +3.4 % peak power.
- Restricted engines go flat above choke rpm: upshift as early as possible while keeping post-shift rpm on the plateau (n_shift ≥ n_choke × gear step); revs beyond that buy nothing.
- Less power → drag matters more; re-check wing level and gearing after every BoP power change.
- Mass sensitivity: lap time rises ≈ 0.1–0.3 × the relative mass increase — get the exact, track-specific number from the sim.
- Energy-per-stint racing rewards efficiency: low drag and well-placed lift-and-coast.
- Archive the event BoP with every setup sheet; data comparisons across BoP versions are meaningless otherwise.

## By car category

### GT3

SRO/IMSA/WEC BoP via restrictor or boost table, weight, sometimes ride height and fuel/refuel parameters. Teams cannot change the engine — the engineering response is wing, ballast placement within rules, shift points and strategy.

### GT4

BoP by weight and power (often via ECU power limitation); otherwise very similar logic to GT3 with more road-car content.

### TCR

Weight ballast, power (boost/ECU limit) and ride height adjustments per car; compensation weight can also be success-based in some championships.

### LMP2

Spec Gibson V8 with a defined power level; different settings may apply at Le Mans vs other rounds. No manufacturer BoP inside the class, but class-to-class performance windows are set by the organisers.

### Hypercar (LMH/LMDh)

BoP on minimum weight, maximum power (incl. power above a speed threshold), energy per stint and, for LMH AWD, the front-axle deployment speed. All measured by FIA torque sensors and fuel-flow/energy meters.

### IndyCar

Not BoP but performance levers: boost level per track type and push-to-pass (extra boost for a limited total time per race) — strategy-relevant like an energy budget.

### Super Formula

Fuel-flow-limited engines; the Overtake System raises fuel flow for a limited total time per race — a deployable energy budget the engineer and driver must manage.

## References

- Segers, Analysis Techniques for Racecar Data Acquisition, 2nd ed. (SAE 2014): §4.1 Torque and Horsepower (power and drag relations used for BoP sensitivity)
- Segers, Analysis Techniques for Racecar Data Acquisition, 2nd ed. (SAE 2014): §16.1 Fuel Consumption (fuel/energy accounting used under energy limits)
- Other: FIA WEC / SRO / IMSA BoP bulletins (check per event; values change)
