# Limited-slip types: plate/ramp, viscous, Torsen, active

> Plate-and-ramp (Salisbury) diffs lock in proportion to input torque plus a preload; viscous diffs respond to speed difference; Torsen gear diffs to torque ratio; active diffs to a controller. Each has a distinct signature on track.

Area: Differential · Starting level: L1 Foundation · Updated 2026-11-16
Source page: https://race-engineer-academy.vercel.app/lesson/diff-lsd-types

## L1 · Foundation

All limited-slip differentials (LSDs) add a **locking torque** that resists a speed difference between the wheels. They differ in *what that locking depends on*:

| Type | Locking depends on | Typical use |
|---|---|---|
| **Plate / ramp (Salisbury)** | input torque (via ramp angles) + preload spring | GT, prototypes, most formula cars, TCR |
| **Viscous (VLSD)** | speed difference between wheels (fluid shear) | road cars, older rally/touring, centre diffs |
| **Torsen / helical (ATB)** | torque ratio between wheels (gear friction), TBR ≈ 2–4 | road cars, some FWD racing |
| **Active / e-diff** | controller-commanded clutch pressure | road supercars, Ferrari Challenge (road-car E-Diff, not team-adjustable), F1 (driver-adjustable maps) |
| **Spool** | fully locked | karts (solid axle), some oval/drag applications |

**Plate/ramp is the racing standard.** A clutch pack (alternating plates splined to the diff case and to the side gears) sits on each side. The input torque arrives through cross-pins sitting in **V-shaped ramps** in pressure rings. Under torque the pins climb the ramps, pushing the pressure rings apart and squeezing the clutch packs. More torque → more clamping → more locking. Separate ramp angles on the two faces of the V give different behaviour in **drive (power)** and **coast (engine braking / overrun)**. A spring stack gives **preload** — locking even at zero torque.

**Viscous**: shear of silicone fluid between plates; locking grows with speed difference, so it only works after a wheel has already started to spin, and fluid heating changes the characteristic ("hump" mode). Rare in modern circuit racing.

**Torsen**: worm/helical gear friction gives a fixed **torque bias ratio**. Weak point: if one wheel has zero grip (lifted inside wheel over a kerb), TBR × 0 = 0 — no torque to the other wheel either. Some versions add preload to soften this.

**Active**: a hydraulic clutch pack whose pressure is set by a controller from speed, lateral g, steering, throttle. Can provide different locking in entry, mid-corner and exit — the ideal, and therefore often restricted by regulations.

## L2 · Practitioner

**Practical signatures on track.**

**Plate/ramp:**
- Locking ∝ torque: strong lock under full throttle in low gears, little at part throttle mid-corner (where **preload** dominates).
- Drive vs coast independently tunable via ramp angles: e.g. 40° drive / 60° coast (illustrative). A lower angle = more locking (see next lesson).
- Plate wear reduces preload over mileage → behaviour drifts. Measure breakaway torque routinely.
- Chatter/"clunk" at low speed in pit lane and tight hairpins is normal with high preload.

**Viscous:**
- Response lag: locking builds only with speed difference, so it "lets the wheel go" then catches it. Drivers feel delayed traction; the temperature sensitivity makes it inconsistent over a stint.

**Torsen / ATB:**
- No locking without torque and none if one wheel is unloaded — weakness over kerbs and on lifted wheels in FWD touring cars, and a reason TCR teams prefer plate LSDs.
- Smooth, no plates to wear, little maintenance.

**Active:**
- Entry, apex and exit locking can be set independently and even per corner (F1 drivers adjust "diff entry/mid/exit" on the wheel).
- Needs pressure sensing, a control strategy and fail-safe; banned or spec-limited in most of the categories in this academy (check rules). Many road-car-derived one-make or GT4 cars use sealed or spec passive mechanical LSDs (e.g. Porsche Carrera Cup, where the road 911 GT3 has an electronically controlled rear diff lock; Lamborghini Super Trofeo, mechanical LSD with capped preload). The exception in this academy is the Ferrari 296 Challenge, which keeps the road car's electronically controlled E-Diff (integrated with TC via the 6D sensor, not adjustable by teams): the driver's levers are the TC and ABS positions, so the engineer's job there is coaching their use, not changing hardware.

**Choosing among options** (when you can): plate/ramp offers the best tunability per corner phase for passive systems; preload + drive ramp + coast ramp + number of friction faces = four degrees of freedom. Most series restrict some of them — in GT3 often only preload is free, sometimes with a choice of homologated ramp sets.

**Maintenance and checks**: diff oil (often shared with gearbox) temperature; plate wear measurement; breakaway torque test at each rebuild and ideally each event (car on stands, one wheel held, torque wrench on the other — a few seconds of rotation to read the steady slip torque). Always note the test convention: with the gearbox in neutral the case turns freely and the reading is about **half** the left–right torque difference the diff can sustain (see next lesson).

## L3 · Advanced

**Mathematical characterisation.**
- **Plate/ramp:** $T_{lock} = T_{pre} + k\, |T_{in}|$, with $k$ different in drive and coast. A piecewise-linear torque-sensing law with an offset.
- **Viscous:** $T_{lock} = c\,|\Delta\omega|^{n}$ with $n ≈ 0.8$–1 and $c$ decreasing with fluid temperature. A speed-sensing damper between the wheels — it adds **yaw damping** proportional to the wheel speed difference. Shear torque vanishes as $\Delta\omega \to 0$, so it never locks the axle (except in hump mode): in steady cornering it acts as a soft, speed-dependent coupling, not a spool.
- **Torsen:** $T_{high}/T_{low} \le TBR$ — equivalently $T_{lock} = \frac{TBR - 1}{TBR + 1} |T_{in}|$, a pure torque-sensing law without offset. TBR 3 corresponds to $k = 0.5$.
- **Active:** $T_{lock} = \mu\, n\, r_m\, A_p\, p(t)$ with $p(t)$ commanded — any law the controller implements, within actuator bandwidth (≈ 10–30 Hz).

**Equivalence.** A plate diff with $k = 0.5$ and zero preload is, in drive, equivalent to a Torsen with TBR 3. A Torsen also biases torque in coast, but with a ratio fixed by its gear geometry (often near-symmetric; some designs deliberately differ between drive and coast) and with little or no preload. The plate diff can set its coast locking independently of drive (separate ramp face) and add a tunable preload. That's why the plate type dominates circuit racing: the locking law can be shaped to the corner phase.

**Why active diffs are so powerful.** A passive diff's locking is a function of input torque, but the *desired* locking depends on corner phase: low on entry and apex for rotation (but enough for stability on the brakes), high on exit for traction, with a careful transition around the moment the inside wheel would start to spin. A controller with lateral g, steering and yaw-rate inputs can approximate this; a passive diff must compromise. Where actives are banned, engineers approximate phase-dependence by combining **preload** (dominant at low torque: mid-corner and light coast), **coast ramp** (entry under engine braking), and **drive ramp** (exit), plus engine-braking maps and TC.

## Key formulas

**Plate/ramp locking law**

$$T_{lock} = T_{pre} + k\,|T_{in}|$$


**Torque bias ratio ↔ locking coefficient**

$$TBR = \frac{1 + k}{1 - k} \;\Leftrightarrow\; k = \frac{TBR - 1}{TBR + 1}$$


**Viscous locking**

$$T_{lock} = c\, |\Delta\omega|^{n}$$


## Trackside takeaways

- Plate/ramp: locking = preload + k × input torque; separate drive and coast ramps.
- Viscous reacts to speed difference (lag, temperature-sensitive); Torsen to torque ratio (fails with a lifted wheel).
- Active diffs give phase-specific locking — powerful and therefore mostly regulated out.
- TBR 3 ≡ k = 0.5 in drive.
- Measure breakaway (preload) torque routinely: plate wear makes the diff drift.

## By car category

### GT3

Plate/ramp LSD; preload adjustable (spring stack), ramp sets and plate count limited by homologation — often one or a few options.

### TCR

Plate-type front LSD typical; Torsen-type helical diffs suffer when the inside front lifts over kerbs.

### One-make Cup

Varies by series: Porsche Carrera Cup and Lamborghini Super Trofeo run sealed/spec mechanical LSDs; Ferrari Challenge keeps the road car’s electronically controlled E-Diff (integrated with TC via the 6D sensor, not adjustable by teams); the driver’s levers are the TC and ABS positions, so the job there is coaching their use. Check the series technical rules.

### FIA F2

Spec plate-type LSD; adjustments are limited to what the series permits (typically preload within a range).

### IndyCar

Passive mechanical LSD; setup options defined by the spec and rules.

## References

- Milliken & Milliken, Race Car Vehicle Dynamics (SAE 1995): Ch. 20 Driving and Braking (limited-slip differentials, locking characteristics)
- Other: Manufacturer LSD service documentation (e.g. Drexler, Hewland, Xtrac) (ramp angle and friction-face conventions vary by supplier – check the manual for your unit)
