# Differentials in specific cars: GT3, formula cars & on-wheel diff maps

> What you can change depends on the category: GT3s usually offer preload (sometimes homologated ramp/plate options), spec formula cars offer little, and the F1-style hydraulic diff with entry/mid/exit maps on the wheel shows what an unrestricted diff can do.

Area: Differential · Starting level: L2 Practitioner · Updated 2026-11-16
Source page: https://race-engineer-academy.vercel.app/lesson/diff-car-specific

## L1 · Foundation

**GT3 (and GT4, most one-makes; Ferrari Challenge keeps an electronic E-Diff).** Mechanical plate/ramp LSD in the transaxle. Typically:
- **Preload** adjustable via spring/shim stack — the main tool.
- **Ramp angles** and **plate count**: fixed by homologation or a small number of homologated options (e.g. a "standard" and an "alternative" ramp set). Check the homologation form and BoP documents.
- Changing anything usually means removing the diff — not a between-runs change.
- Many teams run one baseline per car model and adjust preload per track: lower preload for tracks with many slow, tight corners (rotation), higher for fast flowing tracks and wet (stability, traction at low torque).

**TCR (FWD).** Front mechanical LSD, usually homologated with preload as the free parameter. Higher preload = traction and stability on exit but heavier steering, torque steer and understeer on turn-in.

**Formula ladder (F4, FR, F3, F2).** Spec cars with spec diffs:
- F4/FR: diff configuration largely fixed by the series; engineers work around it with roll stiffness and balance.
- F3/F2: plate-type LSD with **limited options** (typically preload within a permitted range; ramps/plates spec). The diff is still important on slow exits (F2 has high power and no TC), so preload choice matters.

**Prototypes and IndyCar.** Passive mechanical LSDs with preload and (where allowed) ramp choices; IndyCar has different street/road vs oval approaches.

**On-wheel diff maps (F1 reference).** Formula 1 uses a hydraulically actuated clutch-pack diff whose locking is mapped by corner phase. Drivers have rotaries/switches for **diff entry, mid and (on-throttle) exit**, and adjust them corner by corner during a lap. It shows what an engineer would do with a free diff: low locking on entry/mid for rotation, high on exit for traction — but in the categories of this academy you generally have to approximate that with preload and ramps.

## L2 · Practitioner

**Working with a GT3 preload-only diff.**
- Establish a **preload sensitivity** per car model: e.g. effect of ±40 Nm on min speed and steering angle in slow corners, on entry stability under braking, and on exit traction (TC activity) — from tests or previous events.
- Choose preload by track character: slow, tight circuits (Hungaroring, Zandvoort, Monaco-like street tracks) → lower for rotation, but watch entry stability under heavy braking; fast circuits (Spa, Silverstone) → diff effects smaller, choose for stability and traction in the few slow corners before long straights.
- Wet: lower torque levels make preload relatively more important; many engineers keep or slightly raise preload for stability and traction at low torque — but others lower it for rotation. Decide with the driver's style and data from wet running.
- Tyre degradation: as the rear degrades, higher locking puts more longitudinal force and slip work on the outside rear (and scrubs the inside), raising its temperature. For long stints, err slightly less locked if the rear is the limiting tyre.

**Spec formula cars with limited options (F2/F3).**
- Because options are few, use the diff for **one clearly identified problem** (e.g. slow-corner rotation or inside spin on hairpin exits) and solve the rest with mechanical balance (ARBs, springs) and aero.
- Inside-wheel spin on F2 exits is often better addressed by rear roll stiffness and driver throttle than by maximum preload, which also costs rotation.

**On-wheel diff maps — how they're used (F1 / development cars):**
| Phase | Typical use |
|---|---|
| Entry | high locking for stability in big braking zones; lower for slow corners to help turn-in |
| Mid | low to free apex rotation; increase if the rear floats mid-corner |
| Exit (on-throttle) | medium-high for traction; reduce if exits snap on worn tyres |
Drivers change them per corner and through the stint as the rear degrades — the engineer supplies a baseline per corner and coaches changes from data.

**Regulation check before any change**: diff type, adjustability and whether driver-adjustable diff settings are allowed vary by series and year — read the technical regulations and homologation papers, not the forum.

## L3 · Advanced

**Why the regulations restrict diffs.** An active diff with phase-dependent locking is effectively a yaw-moment controller: it can add rotation on entry and stability/traction on exit, partially decoupling balance from mechanical setup. It also acts as a traction aid. In categories where TC is banned (F2, F3, IndyCar) or performance must be balanced (GT3, Hypercar), active diffs would undermine both. Hence passive mechanical diffs with limited tuning are the norm.

**Approximating phase-dependent locking with a passive diff.** Engineers combine:
- **Coast ramp + engine braking map** (where available) → entry locking;
- **Preload** → mid-corner locking (low torque);
- **Drive ramp + faces** → exit locking scaled with torque;
- **Gear choice** → wheel torque level, hence locking via ramps in a given corner;
- **TC slip targets** → limit inside spin that would otherwise flip the diff state.

The design question for a GT3 with preload-only: since $T_{lock} = T_{pre} + k T_{in}$ and k is fixed, preload is your only knob to move *all* phases — but with a different relative effect: large in mid-corner and coast (small T), small on exit (large T). That's why preload is the right "rotation" tool and the wrong "traction" tool on such cars.

**On-wheel maps in the model.** A hydraulic diff realises $T_{lock} = f(\text{phase}, V, a_y, \delta, T_{in})$; the driver's entry/mid/exit selectors shift sub-tables. The engineer's design work: identify phase transitions robustly (brake pressure threshold, throttle threshold, lateral g), avoid abrupt torque changes at transitions (rate limits), and ensure fail-safe behaviour (pressure loss → defined default locking). The lessons transfer directly to passive-diff setups: they tell you **which phase** needs which locking, and then you ask which passive parameter can get closest.

**Hypercar specifics.** Hybrid torque on the driven axle (LMDh: MGU in the gearbox, upstream of the rear diff) passes through the same diff; regen on coast adds to engine braking → more coast locking under regen. Friction brakes act at the hubs, downstream of the diff, so when brake-by-wire swaps rear friction braking for regen at the same total rear torque, the coast torque seen by the ramps rises. Entry stability must therefore be evaluated with representative regen levels in each braking zone — an entry balance tested in a low-regen energy mode can feel different with high regen.

## Key formulas

**Relative effect of preload on total locking**

$$\frac{\partial T_{lock}/\partial T_{pre}}{T_{lock}} = \frac{1}{T_{pre} + k T_{in}}$$


## Trackside takeaways

- GT3: preload is the main free parameter; ramps/plates fixed or homologated options — check the form.
- Preload acts most on mid-corner and coast (low torque), least on full-throttle exits.
- F2/F3: limited diff options — use them for one clearly identified problem; fix the rest with balance.
- On-wheel diff maps (F1) show the ideal: low entry/mid locking for rotation, higher exit locking for traction.
- Hybrid regen through the driven axle adds coast locking — evaluate entry with representative regen.
- Always confirm diff freedom in the technical regulations and homologation papers.

## By car category

### GT3

Mechanical LSD with adjustable preload; ramps/plates per homologation. Typical practice: lower preload for tight tracks, higher for wet/fast tracks; verify with entry stability.

### GT4

Road-car-derived mechanical LSD with limited or no adjustment; balance is mostly tuned with ARBs and aero.

### One-make Cup

Diff usually sealed/spec; teams may not adjust it at all — drivers adapt technique (throttle on entry, gear choice).

### TCR

Front plate LSD with homologated preload range; steering effort and torque steer limit how much locking drivers accept.

### FIA F2

Limited options (spec LSD, preload within range): high power without TC makes exit inside spin the main diff question.

### FIA F3

Spec LSD with limited adjustment; low aero in slow corners makes preload visible on rotation.

### Hypercar (LMH/LMDh)

Passive LSDs; hybrid regen/deployment on the driven axle interacts with coast/drive locking.

### IndyCar

Mechanical LSD with series-permitted adjustments; street vs road vs oval philosophies differ greatly.

### Super Formula

Spec drivetrain with limited diff adjustment; high downforce reduces diff influence in fast corners but slow hairpins remain diff-sensitive.

## References

- Milliken & Milliken, Race Car Vehicle Dynamics (SAE 1995): Ch. 20 Driving and Braking
- Other: Series technical regulations & GT3 homologation forms (diff type and adjustability per category)
- Segers, Analysis Techniques for Racecar Data Acquisition, 2nd ed. (SAE 2014): §4.2 Traction and Longitudinal Slip (differential work evaluation via slip channels)
