# Comparing laps: delta time, segment times and track mapping

> Find where time is gained or lost before asking why. Delta-time channels, segment times, theoretical best laps and accurate distance alignment are the backbone of every debrief.

Area: Data Acquisition & Analysis · Starting level: L1 Foundation · Updated 2026-11-16
Source page: https://race-engineer-academy.vercel.app/lesson/daq-lap-comparison-delta-time

## L1 · Foundation

**Start with "where", then "why".** Performance analysis begins by locating the gain or loss, not by staring at dampers.

**Segment (sector) times.** Place virtual beacons around the lap – on straights, or splitting corners into entry/apex/exit – and the software tabulates time per segment for every lap. Two derived numbers:

- **Theoretical best lap** = sum of the best segment times in the run. It estimates the potential of the package. Good drivers in a clean run get within 0.1–0.3 s of it.
- **Best rolling lap** = fastest full-lap time measured between *any* beacon pair (not necessarily start/finish). Useful when traffic spoiled every proper lap, because it was actually driven.

**Overlays and delta time.** Overlay speed traces against distance and add the **delta-time** channel: the running time difference between two laps at each point of the lap. The slope tells you where time changes; the final value is the lap-time difference.

**Track maps.** Software builds the map from speed and lateral g (inertial mapping) or GPS. Colour it by braking, throttle or delta to see the lap at a glance.

## L2 · Practitioner

**Reading delta time.** Define

$$\Delta t(s) = t_{B}(s) - t_{A}(s)$$

with $t(s)$ the running lap time at distance $s$. Positive and rising means lap B is losing. The *slope* $d\Delta t/ds$ is the instantaneous loss rate; equivalently

$$\frac{d\Delta t}{ds} = \frac{1}{V_B(s)} - \frac{1}{V_A(s)}$$

so a speed deficit costs most time where speeds are low. Rule of thumb: a constant speed deficit $\Delta V$ over a distance $d$ at speed $V$ costs $\Delta t \approx d\,\Delta V/V^2$. Being 2 km/h slower over a 300 m straight at 200 km/h costs ~0.05 s; being 2 km/h slower for 60 m through an 80 km/h hairpin costs ~0.07 s.

**Why corner exit matters.** An exit-speed deficit persists down the whole following straight (until both cars approach top speed or brake). The delta channel shows this as a steady ramp after the corner – the most valuable losses to fix are therefore exits onto long straights.

**Segment pitfalls.**
- More segments always give a faster theoretical lap. Segers' Spa example: 7 segments gave a theoretical lap 1.42 s under the best real lap, 3 segments only 0.42 s. Start with few segments, add more where you need detail.
- Beacons placed at apexes make segments sensitive to line variations; place them on straights where possible.
- A line that is faster in one segment may compromise the next – the theoretical lap can be unachievable.

**Distance alignment.** Distance from wheel speed drifts with lock-ups, wheelspin and tyre radius changes, so the same corner can be offset by several metres. Check alignment with high-rate damper data: road bumps are a fingerprint of the track. If the bump spikes of two laps don't line up, the overlay is misaligned there (Segers shows a 6 m offset after a single lock-up). GPS-fused distance largely removes the problem.

## L3 · Advanced

**Delta time is a cumulative integral – read the slope, not the level.** A large delta at the end of a sector may come from one 50 m zone; everything after it is flat. Engineers new to data often attribute the whole deficit to the corner where it is *displayed* largest, rather than where the slope was steep.

**Time-slip rate formulation.** Some software expresses the loss rate as a percentage speed difference (time-slip rate) and integrates it (time slip). To first order this equals the delta-time channel – Segers notes both give the same result – but the exact slope is $(V_A-V_B)/(V_A V_B)$, so a 20 % speed deficit costs 25 % more time, not 20 %. Running lap time itself is just the logger time stamp at each distance sample; both methods depend on the same distance alignment, and that alignment is the real accuracy limit.

**Alignment strategies:**
1. **Beacon offset** – shifts the whole lap; fixes the start but not mid-lap drift.
2. **Corner-based re-alignment** – software stretches distance between identified features (apex minimum speeds, braking points) so each corner aligns.
3. **Road-profile correlation** – cross-correlate high-pass filtered damper signals between laps in windows; the lag that maximises correlation is the distance offset.
4. **GPS/IMU fused position** – best, typically within 1 m with a good receiver and inertial blending.

**Missing beacons.** Recognisable road features in the damper trace can be used to insert beacons manually when the IR beacon or GPS gate fails, and to sanity-check lap distance (lap distances should match within ~0.5 % on a clean line).

**Comparing across conditions.** When comparing different runs (fuel, tyres, track evolution), normalise first: fuel-correct lap times, compare like-for-like tyre age, and look for systematic offsets that span the whole lap (grip change) versus local ones (driving or setup). A uniform small positive slope everywhere suggests weight or grip; a localised step suggests a corner-specific issue.

## Key formulas

**Delta time (running time difference)**

$$\Delta t(s) = t_B(s) - t_A(s)$$

- s: lap distance (m)
- t_A, t_B: running lap time of laps A and B at distance s (s)

**Loss rate from speed difference**

$$\frac{d\Delta t}{ds} = \frac{1}{V_B(s)} - \frac{1}{V_A(s)} \approx \frac{V_A - V_B}{V^2}$$

- V: local speed (m/s)

**Theoretical best lap**

$$t_{theo} = \sum_{k=1}^{N} \min_{laps}\, t_{seg,k}$$

- N: number of segments
- t_{seg,k}: time in segment k (s)

## Trackside takeaways

- Locate the loss with delta time before investigating its cause.
- Read the slope of delta time; the level only accumulates history.
- Speed deficits cost most at low speed; exit deficits onto long straights are the most expensive.
- More segments = more optimistic theoretical best; place beacons on straights.
- Verify distance alignment with damper bump fingerprints or GPS before comparing a specific corner.

## By car category

### GT3

In Pro-Am line-ups, the theoretical best per driver vs the pro reference is a clean coaching KPI; best rolling laps help when practice is full of traffic (40+ car fields).

### One-make Cup

Team-mate overlays in identical cars: delta time slope at corner exits is usually where the junior driver loses most.

### FIA F2

Very short qualifying – best rolling lap and segment analysis of the single push lap matter; compare against team-mate on the same tyre age.

### Super Formula

High cornering speeds compress the time cost of small speed deficits; look at entry/apex segments in high-speed corners such as Suzuka S-curves.

### LMP2

Multi-class traffic makes clean laps rare; rely on segment bests and rolling laps per driver.

## References

- Segers, Analysis Techniques for Racecar Data Acquisition, 2nd ed. (SAE 2014): §3.2 Lap Markers and Segment Times
- Segers, Analysis Techniques for Racecar Data Acquisition, 2nd ed. (SAE 2014): §3.3 Comparing Laps (instantaneous/cumulative variance, time slip, road-profile alignment)
- Segers, Analysis Techniques for Racecar Data Acquisition, 2nd ed. (SAE 2014): §3.4 Track Mapping
- Milliken & Milliken, Race Car Vehicle Dynamics (SAE 1995): Ch. 1 The Problem Imposed By Racing (lap-time sensitivity to grip and speed)
