# Kerb riding and high-speed damping control

> Kerbs and big bumps drive shaft velocities to several hundred mm/s. High-speed bump lets the wheel climb without launching the car, high-speed rebound returns it to the ground without bouncing, and the whole package (springs, bump stops, ARBs, ride height) decides whether the car can use kerbs.

Area: Dampers · Starting level: L2 Practitioner · Updated 2026-11-16
Source page: https://race-engineer-academy.vercel.app/lesson/dampers-kerbs-high-speed

## L1 · Foundation

### What happens on a kerb
Hitting a kerb pushes one or two wheels up in a few hundredths of a second. Shaft velocities of **200–600 mm/s** (sausage kerbs and high kerbs up to ~1 m/s) are typical – far into the high-speed range.

- **High-speed bump (compression)** decides how much of that impact goes into the chassis. Too stiff → the force spike lifts and launches the car, the other tyres lose load, the driver feels a "kick". Too soft → the suspension uses all its travel and hits the bump stops hard (which is even stiffer).
- **High-speed rebound (extension)** decides how quickly the wheel comes back down after the kerb. Too stiff → the wheel "hangs" in the air, the tyre loses contact, and repeated kerbs pack the car down. Too soft → the wheel springs back and bounces, unsettling the car.

A car that "rides kerbs well" lets the driver straight-line chicanes and use exit kerbs without losing the rear – often worth several tenths per lap at tracks like Monza, Zandvoort, Sebring, Bathurst or street circuits.

**It's never only dampers.** Single-wheel stiffness (corner spring + about half the ARB rate + bump stops), ride height and bump-stop gap all decide kerb behaviour. With the ARB rate quoted as the usual per-wheel rate in pure roll, a single-wheel kerb strike sees half of it (the bar twists half as much as when both wheels move opposite) – so a stiff ARB still transmits a large share into the strike.

## L2 · Practitioner

### Diagnosing and tuning kerb behaviour
**Data to look at**
- Damper velocity peaks at each kerb (bump and rebound) and the **time to settle** (number of oscillations after the strike).
- **Damper position**: did it reach the bump-stop gap? Hit full droop on the way back?
- Vertical acceleration of chassis (and hub, if fitted) – spikes of 3–6 g on the chassis are common, hub much higher.
- Steering and yaw-rate response just after the kerb: driver corrections reveal instability.
- Lap time segment: compare laps with and without kerb use.

**Typical moves**
| Symptom | Likely cause | Try |
|---|---|---|
| Car launched/"kicked" by kerb | HS bump too stiff or blow-off too high, stop engaged | softer HS bump, more bump-stop gap, softer ARB |
| Wheel hangs, rear steps out after exit kerb | HS rebound too stiff / packing down | less HS rebound |
| Car bounces after kerb, takes several cycles to settle | HS rebound too soft | more HS rebound |
| Floor/plank strikes on kerbs | ride height / heave too soft or packers | ride height +, packers, stiffer heave |

**Packing down / jacking.** Over a series of bumps or a "sawtooth" kerb, a damper with much more rebound than bump at high speed can't extend fully between hits: the car sinks lower with each hit (packs down), losing travel and hitting stops. The opposite (bump ≫ rebound) jacks the car up. Look at the mean damper position across a kerb sequence.

**Dedicated kerb setup decisions** are a trade: softer HS bump and more gap for kerbs usually costs a little platform on smooth high-speed sections. Some dampers offer a **hydraulic bump stop** or blow-off valve to keep LS/medium-speed control while capping kerb forces.

## L3 · Advanced

### The physics of a kerb strike
A kerb is a displacement input with a very high velocity: a 40 mm step kerb at 150 km/h taken over ~0.3 m length rises in ~7 ms – a velocity input far above any body frequency. The damper force for a linear HS slope is $F = c_{HS}\,v$; at 500 mm/s with $c_{HS}$ = 7 N·s/mm (damper) that's 3.5 kN – comparable to the static corner load. The impulse transmitted to the body is roughly $\int F\,dt$ – so for a given kerb, **HS bump force × duration** sets body disturbance. Blow-off (knee) caps $F$, limiting the impulse.

**Wheel dynamics after the strike.** The unsprung mass, launched upward, is restored by the spring + tyre and damped by HS rebound. With wheel ζ ≈ 0.3–0.5 and $f_{hop}$ ≈ 15 Hz, the wheel settles in ~1–2 cycles (~70–130 ms). Too little ζ → visible ringing at $f_{hop}$ in the damper-position trace and tyre-load spikes; too much rebound → the wheel can't follow the falling side of the kerb, contact is lost (zero tyre load) for tens of ms – lateral grip at that corner disappears, which is the "rear steps out after the kerb" feeling.

**Tyre load during kerbs** can be estimated with hub accelerometers or from pushrod load plus unsprung inertia (after Segers §12.8, Eq. 12.35, which uses dynamic components only; for absolute load add $g$): $F_{cp} = F_{susp} + m_u(a_{hub} + g)$, upward positive, with $F_{susp}$ the total spring + damper + bump-stop force referred to the wheel (plus the vertical component of link forces under braking/traction). If $a_{hub}$ is the raw accelerometer reading (≈ +1 g at rest), it already contains $g$. Contact-patch load reaching zero is the objective failure criterion.

**Kerb compliance budget**
- Single-wheel rate (corner spring + ½ ARB per-wheel roll rate + ¼ axle heave rate) – lower = less force spike.
- HS bump slope and blow-off – lower = less impulse.
- Bump-stop gap – enough to avoid stop contact on the kerb.
- HS rebound – enough to avoid ringing, not so much to pack down.

**Packing analytically.** Under periodic input of amplitude $X$ and frequency $\omega$, an asymmetric damper (bump $c_b$, rebound $c_r$) produces a mean force of $\frac{1}{\pi}(c_r - c_b)\,\omega X$ (bilinear model, velocity amplitude $\omega X$) that must be balanced by a spring offset: $\Delta x_{mean} \approx \frac{(c_r-c_b)\omega X}{\pi k}$. Fast, large inputs (kerb sequences) and soft springs maximise packing.

## L4 · Expert

### Advanced considerations
- **Cavitation and hysteresis at high velocity**: insufficient gas pressure lets the rebound chamber cavitate after a hard bump stroke → rebound force arrives late, wheel overshoots. Check dyno hysteresis loops at 300–500 mm/s.
- **Kerb-strike modelling** in simulation requires the tyre's enveloping behaviour (the tyre "swallows" short kerbs – effective input is filtered by contact-patch length), damper non-linearity and bump-stop curves. Linear quarter-car models overestimate peak forces on sharp kerbs.
- **Chassis torsion** absorbs part of a single-wheel strike on less stiff chassis (GT4/TCR) and redistributes load diagonally (warp). Warp is not resisted by third (heave) springs, but it *is* resisted by corner springs and ARBs (front and rear roll stiffness acting roughly in series, with the body free to roll), by the tyres and by chassis torsion. A softer chassis adds compliance in series with the suspension: it lowers warp stiffness, so less of a single-wheel strike is passed diagonally to the opposite corners, at the cost of less precise load distribution.
- **Driver-specific**: some drivers attack kerbs, others avoid them. Analyse kerb usage per driver before changing the car; in multi-driver endurance cars, choose a setup that is *robust* to kerb use rather than optimal for one style.
- **Regulatory/track factors**: track limits enforcement and kerb shapes (sausages, negative kerbs) change from event to event; a kerb setup is circuit- and even session-specific (wet: less kerb use).

## Key formulas

**Damper force at high velocity (linear HS slope)**

$$F_{HS} = F_{knee} + c_{HS}\,(v - v_{knee})$$

- F_{knee}: force at knee/blow-off (N)
- c_{HS}: high-speed slope (N·s/mm)
- v_{knee}: knee velocity (mm/s)

**Contact-patch load estimate**

$$F_{cp} = F_{susp} + m_u\,(a_{hub} + g)$$

- F_{susp}: spring + damper + bump-stop force on the hub, referred to the wheel, plus vertical link-force components (N)
- m_u: unsprung mass (kg)
- a_{hub}: hub vertical acceleration, up positive, excluding gravity (m/s²); a raw accelerometer reading already includes g

**Packing offset (bilinear damper, harmonic input)**

$$\Delta x_{mean} \approx \frac{(c_r-c_b)\,\omega X}{\pi\,k}$$

- c_r, c_b: rebound / bump coefficients
- X: input amplitude
- k: spring rate

## Trackside takeaways

- Kerbs produce 200–600+ mm/s shaft speeds: HS bump decides launch, HS rebound decides return.
- Rebound ≫ bump at HS over repeated bumps → car packs down; bump ≫ rebound → jacks up.
- Kerb compliance = single-wheel rate (spring + ½ ARB + ¼ heave) + HS damping + bump-stop gap.
- The failure criterion is contact-patch load reaching zero after the strike.
- Analyse kerb usage per driver and per session before making a kerb setup change.

## By car category

### GT3

Kerb riding is crucial at Monza, Zandvoort, Spa (Bus Stop) and Bathurst; softer HS bump, more front bump-stop gap and softer ARBs are the common package. Watch rear stability on exit kerbs.

### GT4

Softer cars ride kerbs naturally; the limit is often travel/bump stops and damper overheating.

### TCR

FWD cars use kerbs aggressively; inside rear lift is normal. Strut-friction and stop engagement dominate.

### Formula 4

Light cars with stiff ARBs relative to springs: single-wheel stiffness is high – softer ARB often helps more than damping.

### FIA F3

High kerbs can damage the floor/plank and upset the platform; heave packers and corner HS damping are the trade-off.

### LMP2

Endurance: robust kerb behaviour beats ultimate platform – multiple drivers with different kerb use.

### IndyCar

Street courses (Long Beach, St. Petersburg, Detroit) are bump/kerb dominated – HS compliance is a priority.

### One-make Cup

Damper click range is limited; kerb setups often come from ARB and ride-height choices.

## References

- Segers, Analysis Techniques for Racecar Data Acquisition, 2nd ed. (SAE 2014): §11.3 Shock Speed Ranges (kerbs produce very high shock speeds)
- Segers, Analysis Techniques for Racecar Data Acquisition, 2nd ed. (SAE 2014): §12.8 Frequency Analysis from Sensor Data (contact patch load from hub dynamics)
- Milliken & Milliken, Race Car Vehicle Dynamics (SAE 1995): Ch. 22 Dampers
