# Damping ratio and critical damping (body and wheel)

> Damping ratio ζ normalises the damper coefficient against mass and stiffness. Race cars typically run a body damping index ζ ≈ 0.6–0.8 at low shaft speed and wheel ζ ≈ 0.3–0.5 at high shaft speed – single-corner indices for comparing setups, not the true modal damping of the car.

Area: Dampers · Starting level: L1 Foundation · Updated 2026-11-16
Source page: https://race-engineer-academy.vercel.app/lesson/dampers-damping-ratio

## L1 · Foundation

### How much damping is "enough"?
For a mass $m$ on a spring $k$, **critical damping** is the smallest damping that returns the mass to rest without overshoot:

$$c_{crit} = 2\sqrt{k\,m}$$

The **damping ratio** compares the actual coefficient to it:

$$\zeta = \frac{c}{c_{crit}} = \frac{c}{2\sqrt{k\,m}}$$

- ζ = 0: oscillates for ever.
- ζ ≈ 0.2–0.3: road-car comfort – a couple of visible overshoots.
- ζ ≈ 0.6–0.8: one small overshoot and settled – the race-car body target.
- ζ = 1: critically damped – no overshoot.
- ζ > 1: over-damped – slow return; on a car, the tyre is "held" and can lose contact.

A race car has **two** systems on each corner:
1. **Body (sprung mass)** on the ride rate, ~2–5 Hz → target **ζ ≈ 0.6–0.8** (LS damping).
2. **Wheel (unsprung mass)** between suspension spring and tyre, ~12–20 Hz → target **ζ ≈ 0.3–0.5** (HS damping).

The same damper must do both – that's why race dampers are digressive.

These body "targets" are **single-degree-of-freedom indices**: a convenient, comparable number per corner. Because the tyre is a second spring in series, the real body-mode damping of a race car is lower (L2/L3).

**Example (GT3 rear corner):** $m_s$ = 305 kg, ride rate 123 N/mm → $c_{crit}$ = 2√(123 000 × 305) ≈ 12 250 N·s/m = 12.3 N·s/mm at the wheel. For ζ = 0.7 → 8.6 N·s/mm at the wheel. With damper MR 0.8 → 8.6/0.64 ≈ 13.4 N·s/mm at the damper.

## L2 · Practitioner

### Using the calculator and reading real dampers
**Body ζ (low speed).** Use the corner sprung mass, the ride rate (or wheel rate – be consistent, see below) and the LS slope of the dyno curve converted to the wheel ($c_w = c_d\mathrm{MR}^2$). Bump and rebound slopes differ; quote both, and their average for an "overall" ζ.

**Wheel ζ (high speed).** The unsprung mass $m_u$ oscillates between the suspension and the tyre:

$$\zeta_w = \frac{c_w}{2\sqrt{(K_w + K_t)\,m_u}},\qquad f_{hop} = \frac{1}{2\pi}\sqrt{\frac{K_w+K_t}{m_u}}$$

GT3 rear: $m_u$ = 55 kg, $K_w$ = 187, $K_t$ = 360 N/mm → $f_{hop}$ ≈ 15.9 Hz, $c_{crit}$ ≈ 11.0 N·s/mm. ζ = 0.4 → 4.4 N·s/mm at the wheel → 6.9 N·s/mm at the damper (HS slope). The LS slope (13.4) is ~1.9× the HS slope – a digressive curve, as expected.

**Typical targets**
| Mode | ζ target | Notes |
|---|---|---|
| Body, LS bump | 0.5–0.7 | lower helps mechanical grip over undulations |
| Body, LS rebound | 0.7–1.0+ | aero cars often > 1 to hold platform |
| Wheel, HS | 0.3–0.5 | too high → tyre skips; too low → wheel hop |

**Practical rules**
- **Spring change ⇒ damping change.** ζ ∝ 1/√k: +20 % spring with the same damper = −9 % ζ. Teams re-click dampers with every spring change to keep ζ constant.
- **Mass change.** Fuel burn (e.g. 100 kg over a stint) raises ζ slightly as the car lightens.
- **Bump stops.** When engaged, $k$ jumps and ζ falls sharply.

**Convention warning.** Teams compute a body damping *index* $c_w/(2\sqrt{k\,m_s})$ with either the wheel rate or the ride rate (tyre in series). For the same damper the ride-rate index is higher by $\sqrt{1+K_w/K_t}$: ≈1.1–1.25 on GT cars (1.23 on the GT3 corner above: 0.70 vs 0.57) and up to ≈1.4 on stiff aero cars where $K_w ≈ K_t$. **Neither is the true modal damping.** The damper does not span the tyre, so in the body mode it only sees the suspension share $K_t/(K_w+K_t)$ of the body motion, and its dissipation scales with the square of that share:

$$\zeta_{body,modal} \approx \zeta_{index,ride}\left(\frac{K_t}{K_w+K_t}\right)^2$$

GT3 corner: 0.70 × (360/547)² ≈ 0.30; a quarter-car eigenvalue calculation gives 0.27 at 3.6 Hz. Pick one index convention, label it in the database, and never compare indices across conventions.

## L3 · Advanced

### Beyond the single-degree-of-freedom picture
**Damped natural frequency**: $f_d = f_n\sqrt{1-\zeta^2}$ is the frequency of *free decay* (e.g. the settling after a kerb or a step): at ζ = 0.7 it is 71 % of $f_n$. The peak of a forced-response PSD/FRF under road excitation sits elsewhere – ≈0.79 $f_n$ for ζ = 0.7 in a base-excited SDOF, and shifted again by quarter-car coupling – so do not back out $f_n$ from a PSD peak with this formula.

**Two-mass (quarter-car) reality.** The damper sits between body and wheel; the tyre (ζ ≈ 0.03–0.05 alone) sits between wheel and road. The body mode is damped through the damper only when the tyre is relatively stiff; when the suspension is much stiffer than the tyre, body and wheel move together, the damper sees little relative velocity, and the body mode becomes *tyre-dominated and poorly damped*. No damper setting fixes this – the remedy is softer suspension in that mode or extra elements (inerter, heave damper).

This already matters at $K_w/K_t ≈ 0.5$, not only when $K_w \gg K_t$. Quarter-car eigenvalues for the GT3 rear corner of L1 ($m_s$ 305 kg, $m_u$ 55 kg, $K_w$ 187, $K_t$ 360 N/mm), sweeping the wheel damping expressed as ride-rate index: 0.3 → modal body ζ 0.12, 0.5 → 0.20, 0.7 → 0.27, ≈0.95 → 0.31 (the maximum, body mode ≈4.0 Hz), 1.6 → 0.21. Beyond the optimum, extra damping **locks the body to the wheel** and the mode migrates toward a ≈4–5 Hz bounce on the tyre springs instead of being damped. A soft road-car corner ($K_w$ 60, $K_t$ 300 N/mm) at index 0.7 still gets ≈0.52 – the gap grows with $K_w/K_t$. Check real damping with a quarter-car eigenvalue calculation, or from the measured ride-height PSD (half-power bandwidth $\zeta ≈ \Delta f/(2 f_n)$, reliable for lightly damped peaks).

**Grip optimum ≠ platform optimum.** For random road input, the damping that minimises contact-patch load variation (CPLV) is lower than the damping that minimises body motion (Segers ch12, fig. 12.16). On a mechanical-grip car (F4, GT4), bias towards the grip optimum; on an aero car the platform optimum carries more lap time, so higher LS ζ. HS ζ stays near the grip optimum on both.

**Modal ζ.** Roll and pitch have different effective masses (Segers eq. 12.28–12.29: the wheel-equivalent body mass in roll is ≈20–40 %, in pitch ≈60–80 % of the quarter-vehicle mass on race cars) and different stiffnesses, so the same corner dampers give different modal ζ:
$$\zeta_{roll} = \frac{C_{\phi f}+C_{\phi r}}{2\sqrt{(K_{\phi f}+K_{\phi r})\,I_{x,eff}}},\qquad C_{\phi} = \frac{c_w t^2}{2}\ \text{per axle}$$
Low roll inertia on its own *raises* this SDOF roll ζ (ζ ∝ $1/\sqrt{K I}$). Roll is nevertheless often the under-damped mode of a race car, for two reasons: (1) the ARBs add $K_\phi$ without adding any damping, and (2) with low equivalent mass and high roll stiffness the tyre becomes comparable in stiffness to the suspension in roll, so the damper sees little relative motion and the tyre's low damping governs the mode (Segers §12.6). Adding bar without adding damping therefore lowers ζ_roll – a reason a stiffer bar can make transient balance "nervous".

**Digressive curves** have amplitude-dependent effective ζ; use equivalent linear damping at the relevant amplitude when comparing to targets.

## L4 · Expert

### Choosing ζ in practice – what top engineers do differently
- **Separate targets per mode and direction**: heave bump/rebound, pitch (front bump with rear rebound on braking), roll (outside bump with inside rebound). With third dampers these can be set separately; with corner dampers only, decide which mode the LS clicks primarily serve on that track.
- **Use rig or on-track FRFs** to set HS damping: sweep clicks and minimise the tyre-load FRF peak near wheel hop and the 2–10 Hz band area. Lap-sim with a quarter-car or full vertical model driven by measured track profiles (from laser + pot + accelerometer reconstruction) gives an objective CPLV metric per click.
- **Aero platform objective**: minimise variance of front ride height and rake at speed (the aero-relevant states) rather than body acceleration – these weightings change the optimum ζ (generally higher LS).
- **Non-linear reality**: friction dominates at very low velocity; at ±2–5 mm/s the damper is effectively locked – ζ is meaningless there. At kerb strikes, blow-off valves make ζ amplitude-dependent.
- **Driver interface**: high LS ζ gives immediate response but transmits more of each input as a load spike; some drivers trade 0.1 ζ for a more progressive limit. Damping ratio is a starting framework, not an answer.

## Key formulas

**Critical damping**

$$c_{crit} = 2\sqrt{k\,m}$$

- k: stiffness (N/m)
- m: mass (kg)

**Damping ratio**

$$\zeta = \frac{c}{2\sqrt{k\,m}}$$

- c: damping coefficient at the wheel (N·s/m)

**Wheel (unsprung) damping ratio**

$$\zeta_w = \frac{c_w}{2\sqrt{(K_w+K_t)\,m_u}}$$

- m_u: unsprung corner mass (kg)
- K_w, K_t: wheel and tyre rates (N/m)

**Wheel-hop frequency**

$$f_{hop} = \frac{1}{2\pi}\sqrt{\frac{K_w+K_t}{m_u}}$$


**Damped natural frequency**

$$f_d = f_n\sqrt{1-\zeta^2}$$


## Trackside takeaways

- ζ = c / (2√(k·m)); use wheel-referred c (c_d · MR²) and a consistent stiffness convention.
- Targets: body LS index ζ ≈ 0.6–0.8 (rebound up to 1+ on aero cars); wheel HS ζ ≈ 0.3–0.5. Body figures are SDOF indices – the true modal body damping is roughly the ride-rate index × (K_t/(K_w+K_t))² (multiply a wheel-rate index by √(1+K_w/K_t) first).
- Wheel hop typically 12–20 Hz; body 2–5 Hz – the digressive curve serves both.
- Change springs → re-click dampers: ζ ∝ 1/√k.
- Roll can be under-damped even when heave is well damped – bars add roll stiffness without damping, and a tyre-dominated roll mode resists damper control.

## By car category

### GT3

Body ~3 Hz, wheel hop ~14–17 Hz with heavy GT wheels/brakes (m_u ≈ 45–60 kg). Bump-stop engagement at speed cuts body ζ significantly.

### GT4

Softer springs: same damper gives higher ζ; limited clicks often mean you are slightly over-damped on smooth tracks and under-damped on bumpy ones.

### Formula 4

Light unsprung masses (~25–35 kg) and soft springs: wheel hop ~15–20 Hz; mechanical grip optimum → keep body ζ moderate.

### FIA F3

Stiff heave with tyre-dominated compliance: heave mode damping is limited by the tyre – watch for lightly damped peaks in ride-height PSD.

### LMP2

Third dampers allow independent heave/pitch damping; corner dampers then tuned primarily for roll and wheel control.

### Hypercar (LMH/LMDh)

Large 18-inch wheels and wide tyres dominate unsprung mass (hybrid motors are chassis-mounted, i.e. sprung; carbon brakes are light). Check HS damping against the measured hop frequency, and treat heave/pitch platform damping with the third elements as the main LS job.

### Super Formula

Very stiff, light car: LS body ζ targets are high and LS clicks have strong effects on entry.

## References

- Milliken & Milliken, Race Car Vehicle Dynamics (SAE 1995): Ch. 22 Dampers
- Milliken & Milliken, Race Car Vehicle Dynamics (SAE 1995): Ch. 16 Ride and Roll Rates
- Segers, Analysis Techniques for Racecar Data Acquisition, 2nd ed. (SAE 2014): §11.4.1 Shock Speed Histogram Shape – A Mathematical Approach (natural frequency, damping ratio, over/under-damped solutions)
- Segers, Analysis Techniques for Racecar Data Acquisition, 2nd ed. (SAE 2014): §12.3 Theoretical Analysis (quarter-car with wheel and tyre)
- Segers, Analysis Techniques for Racecar Data Acquisition, 2nd ed. (SAE 2014): §12.6 Modal Frequency Issues (wheel-equivalent masses in roll/pitch; tyre-dominated roll mode)
