# Lock-up diagnosis: front vs rear, wheel speed vs reference speed

> Detect and classify lock-ups from wheel speeds against a reliable vehicle reference speed, then separate bias, technique, platform and powertrain causes.

Area: Brakes · Starting level: L2 Practitioner · Updated 2026-11-16
Source page: https://race-engineer-academy.vercel.app/lesson/brakes-lockup-diagnosis

## L1 · Foundation

A **lock-up** occurs when a wheel's rotational speed collapses towards zero while the car is still moving: the tyre's slip ratio goes far beyond its optimum (~8–15 % for slicks), braking force falls, lateral grip almost disappears and the tyre can be **flat-spotted** within a fraction of a second, causing vibration for the rest of the stint.

**Slip ratio:**

$$\kappa = \frac{\omega R - V}{V}$$

Under braking $\kappa < 0$; a fully locked wheel has $\kappa = -1$.

**How it shows in the data (Segers §5.4):** the wheel-speed trace of the locking wheel drops almost vertically below the vehicle speed, then jumps back up when the driver releases pressure. Plot all four wheel speeds against a reference speed (GPS), or a slip-ratio channel per wheel.

**Which wheel locks?** Usually the one with the **least load** on the axle with the **most brake** relative to its grip:
- **Inside front** during trail braking (lateral transfer unloads it).
- **Both fronts** in a straight line with too much front bias or a too aggressive initial stamp.
- **Rears** with too much rear bias, over a crest, or when engine braking adds to rear brake torque on downshifts.

**Front vs rear consequences:**
- Front lock: the car goes straight on (no steering response) — safe but costly; flat-spotted fronts.
- Rear lock: the rear loses lateral grip, the car rotates — can spin. Driver feedback is often "the rear stepped out on entry" rather than "rear lock".

**Typical driver comments:** "locking the inside front into T1" (bias, technique, or front geometry/diff), "the rear locks on the downshift" (engine braking / downshift / diff), "locks over the bump" (platform).

## L2 · Practitioner

**Getting a good reference speed.** Under braking every wheel is braked, so no wheel represents true speed. Options:
- **GPS speed** (Doppler, 10–25 Hz, good to ~0.1–0.2 km/h): the best general reference.
- **Integrated longitudinal acceleration** seeded with the speed at brake application: good for 1–2 s, drifts after that.
- **Fastest wheel**: usable without GPS, but fails when all wheels are slipping (heavy braking on a slippery surface).

**Calibrate rolling radius.** Wheel speed = $\omega R_{dyn}$, and $R_{dyn}$ changes with tyre size, wear, pressure, load and speed (growth at high speed). Calibrate each wheel against GPS on a constant-speed straight; otherwise you will see apparent slip of ±2–3 % that isn't real.

**Lock-up channel.** Define per wheel $\kappa_i = (v_i - V_{ref})/V_{ref}$ and flag lock-ups when $\kappa_i < -0.20$ (–20 %) for more than ~50 ms. Count per corner per lap. Run charts per corner show which zones are a problem and whether changes help.

**Diagnosis matrix:**

| Pattern | Likely cause | First actions |
|---|---|---|
| Both fronts, early in zone, every lap | Bias too far forward or stamp too aggressive for the platform | Bias rearward 0.5–1 %, check front damping/pitch |
| Fronts late in zone (low speed) | Pressure not reduced as downforce fades | Driver: progressive release; migration; bias |
| Inside front at turn-in | Trail-braking load on unloaded wheel | Bias, release technique, front ARB/diff entry, toe/camber |
| Rears, high-speed zones | Rear-biased bias with front-heavy aero under pitch, or crest | Bias forward, platform |
| Rears, at downshifts | Engine braking / downshift timing / diff | Engine-braking map, blip, diff coast ramp |
| One wheel, one location | Bump/kerb unloading | Damping, line, local only |
| All wheels, wet | Low μ, bias too far forward, pressure too high | Bias rearward, driver |

**Late-zone front locks on aero cars** are very common: at the start of the zone downforce supports high pressure; as speed falls, the tyres lose load but the driver keeps the pressure. The fix is mainly technique (progressive release), sometimes migration or more rearward bias.

**Misconception:** "a lock-up means the bias is wrong." Many lock-ups are technique (release), platform (bumps) or powertrain (downshifts). Change bias only when lock-ups are systematic on one axle across corners.

## L3 · Advanced

**Precise slip estimation.** For quantitative work (tyre peak-slip identification, ABS tuning), the reference speed must be at the *wheel* location: in a corner, each wheel's ground speed differs by yaw rate × lateral offset: $V_{x,i} = V_x \mp r\,t_i/2$ (track width $t_i$). At 30 °/s yaw rate and 1.6 m track this is ±0.42 m/s — 1.5 % slip at 100 km/h, enough to corrupt inside/outside comparisons. Correct for it before concluding the inside front is "slipping more".

**Brake torque balance at a wheel.** Wheel rotational dynamics (same convention as the formula card, $F_x$ positive when driving): $I_w\dot\omega = T_{drive} - T_{brake} - F_x R$. Under braking $F_x < 0$, so $-F_x R$ is the tyre torque spinning the wheel back up against $T_{brake}$ (and against engine braking, a negative $T_{drive}$). At the onset of lock, $|F_x|$ passes its peak and falls, so $\dot\omega$ diverges: the "knee" in the wheel-speed trace marks the tyre's peak slip. Using $\dot\omega$ and line pressure (→ $T_{brake}$), you can estimate $F_x$ at each instant — a poor man's tyre longitudinal curve per axle, useful for checking whether the bias puts both axles near their peak slip.

**Coupling with the platform.** On a stiff aero car, front ride height under braking drops; if the front hits packers/bump rubbers abruptly, the contact-patch load fluctuates at the tyre-hop frequency (~15–20 Hz) and a wheel can lock momentarily at each unload. Signature: lock spikes synchronised with RH minima or damper velocity peaks. Fix: packer gap, bump-rubber rate, front high-speed bump damping — not bias.

**Diff and lock-ups.** With a locking diff on overrun (high coast ramp/preload), the rear wheels are coupled: the clutch friction moves braking torque from the slower inside rear to the faster outside rear, so the inside rear rarely locks on its own and the axle gives a stabilising yaw moment — but if total overrun torque is too high both rears let go together, abruptly. With an open-ish diff the engine braking is split equally, and the lightly loaded inside rear can lock on its own. Correlate rear lock events with throttle = 0, gear changes and diff settings (see the entry-stability lesson).

**Flat-spot severity.** Energy dissipated in the contact patch during a lock is roughly $F_x\,V\,\Delta t$: a 3 kN front axle force at 40 m/s for 0.3 s is 36 kJ concentrated on one patch — enough to remove a millimetre-scale layer of tread on a slick. Short locks at high speed are worse than long locks at low speed. A vibration complaint after a lock can be confirmed with a wheel-speed or vertical-acceleration FFT at the wheel rotation frequency ($V/(2\pi R)$).

## Key formulas

**Slip ratio**

$$\kappa = \frac{\omega R_{dyn} - V}{V}$$

- \omega: wheel angular speed (rad/s)
- R_{dyn}: dynamic rolling radius (m)
- V: reference ground speed at the wheel (m/s)

**Wheel rotational dynamics**

$$I_w\,\dot\omega = T_{drive} - T_{brake} - F_x R$$

- I_w: wheel+brake inertia (kg·m²)
- F_x: tyre longitudinal force, positive driving (N)

**Wheel ground speed in yaw**

$$V_{x,i} = V_x \mp r\,\frac{t}{2}$$

- r: yaw rate (rad/s)
- t: track width (m)

## Trackside takeaways

- Lock-up = wheel speed collapsing below reference speed; slip ratio approaching −1.
- Use GPS as reference speed and calibrate rolling radii against it on a straight.
- The wheel with least load on the most-braked axle locks first — usually the inside front on trail braking.
- Front lock: car goes straight (safe). Rear lock: car rotates (dangerous) — drivers often report it as oversteer.
- Late-zone front locks on aero cars = pressure not released as downforce fades.
- Lock spikes synchronised with ride-height minima = platform problem, not bias.

## By car category

### One-make Cup

The 992.1 Porsche 911 GT3 Cup has no ABS: lock-up diagnosis and bias work are central, and flat spots can end a race. ABS-equipped Cup cars (the 2026 992.2 911 Cup with Bosch M5 ABS, Ferrari Challenge, Super Trofeo) shift the problem to ABS activity analysis.

### Formula 4

No ABS: lock-ups are frequent and a core coaching topic. The inside front on trail braking and rear locks on aggressive downshifts are classic.

### FIA F3

No ABS and high aero load: late-zone front lock-ups as downforce fades are the typical mistake; tyre allocation makes flat spots expensive.

### FIA F2

No ABS, carbon brakes: cold brakes/tyres on out-laps and after safety cars are high-risk for lock-ups.

### LMP2

No ABS: long stints with tyre double-stints make flat spots very costly; drivers manage bias through the stint.

### GT3

ABS prevents classic locks, but wheel-speed analysis still reveals ABS-limited zones and mis-calibrated wheel-speed sensors after tyre changes.

## References

- Segers, Analysis Techniques for Racecar Data Acquisition, 2nd ed. (SAE 2014): §5.4 Lock-up
- Segers, Analysis Techniques for Racecar Data Acquisition, 2nd ed. (SAE 2014): Ch. 4 (longitudinal slip ratio)
- Milliken & Milliken, Race Car Vehicle Dynamics (SAE 1995): Ch. 2 Tire Behavior (longitudinal slip)
- Milliken & Milliken, Race Car Vehicle Dynamics (SAE 1995): Ch. 20 Driving and Braking
