# Braking analysis with data: quickness, effort, brake points, release & pedal travel

> The standard data toolkit for braking (Segers ch. 5): how fast the driver builds deceleration, how much of the available grip is used, where the brake point is and why it moves, how the release blends into cornering, and what pedal travel and pressure reveal about the hardware.

Area: Brakes · Starting level: L2 Practitioner · Updated 2026-11-16
Source page: https://race-engineer-academy.vercel.app/lesson/brakes-data-analysis

## L1 · Foundation

Braking itself does not make the car faster, but every metre of braking zone you shorten is a metre spent accelerating or at higher speed. Segers' Zolder example: the faster lap spent ~2.6 % less of the lap time decelerating.

Four questions structure any braking analysis:

1. **Quickness — how fast is maximum deceleration reached?** Measure the time from the start of braking to peak longitudinal deceleration, or the slope of the $g_{long}$ trace (the *jerk*, in g/s). Segers quotes < 0.5 s as fast for his GT example (1.49 g reached in 0.48 s, peak slope ~3.1 g/s). Modern high-downforce cars with experienced drivers reach peak pressure in ~0.1–0.3 s.

2. **Effort — is the peak deceleration as high as the car can do?** A first target from Segers (after Buddy Fey): peak braking g ≈ 95 % of peak lateral g, corrected ±2 % for engine position and tyre contact-patch shape. Better: compare with the best braking zones of the fastest driver/lap at the same speed.

3. **Brake point — where does braking start, and is it consistent?** The brake point depends on approach speed (Segers Fig. 5.3 shows two laps 6 km/h apart in *top* speed — not necessarily at the brake point — whose brake points differ by 17 m before the traces merge). If both laps end on the same deceleration curve, the expected shift is $\Delta s \approx V\,\Delta V/a_x$ (from $(V_A^2 - V_B^2)/2a_x$; slightly less if the slower lap is still accelerating). A GT3 at 250 km/h braking at ~1.6 g: 5 km/h more speed moves the brake point only ~6 m. Compare brake points *relative to the speed*, and treat the residual beyond $V\Delta V/a_x$ as technique.

4. **Release / transition — how does braking blend into cornering?** The **combined acceleration** $g_{comb} = \sqrt{g_{lat}^2 + g_{long}^2}$ should stay near the grip limit from the brake point through turn-in to the apex. A **valley** in $g_{comb}$ during the braking phase means grip was left unused (typically braking too early or easing off too soon).

Channels needed: speed (GPS and wheel speeds), $g_{long}$, $g_{lat}$, front and rear brake pressure, ideally pedal travel and steering. With those you can answer all four questions for every braking zone, every lap.

## L2 · Practitioner

**Practical math channels:**

| Channel | Definition | Use |
|---|---|---|
| Brake jerk | $d g_{long}/dt$ (filtered) | Quickness; peak per zone |
| Time to peak | time from $p_F$ > 5 bar to max $|g_{long}|$ | Quickness per zone |
| Combined g | $\sqrt{g_{lat}^2 + g_{long}^2}$ | Valleys = unused grip |
| Brake bias | $p_F/(p_F+p_R)$, gated | Adjuster use, consistency |
| Pressure rate | $dp_F/dt$ | Application/release aggression |
| Release smoothness | std. dev. of $dp_F/dt$ during release | Driver consistency/feel |

**Effort with lateral g (Segers Eq. 5.2).** Using a friction circle approximation, the available deceleration while cornering is $g_{long} = \sqrt{g_{max}^2 - g_{lat}^2}$. A car capable of 1.8 g braking that is cornering at 0.5 g can still decelerate at ~1.73 g: braking capability falls little at small lateral g, which is why most braking can overlap the turn-in phase.

**Early vs late braking.**
- Early braking: valley in combined g at the start of the zone; low initial $g_{long}$ (e.g. 1.0 g where 1.4 g is possible); the driver arrives at the turn-in point too slow and coasts.
- Late braking: high, possibly ABS-limited decel to the apex, lateral g peaking late (mid-corner or after), apex speed lower than the reference, and often a late or compromised throttle point. Segers: if lateral g only peaks at or after mid-corner, suspect a late brake point.

**Approach speed effect.** Overlay laps aligned on distance. Traces that merge after the brake point do not by themselves prove equal braking: the slower lap is still accelerating while the other brakes, so the traces meet at its brake point whatever the first lap did. Compare the brake-point shift with the expected $V\,\Delta V/a_x$ (≈ 6 m for 5 km/h at 250 km/h and 1.6 g on a GT3); only the residual, together with lower initial decel or a combined-g valley, points to a technique difference. Approach-speed differences themselves come from draft or the exit of the previous corner.

**Pedal travel (Segers §5.6).** Pressure vs pedal travel XY plot: dead travel before pressure build-up (free play, knock-back), slope (system stiffness), and scatter (compliance). Over a long stint, more pedal travel for the same pressure means **pad wear** — useful for endurance pad-life tracking. Sudden increase in travel = knock-back (after kerbs) or fluid boiling.

**Comparing drivers.** Line up the same corner: brake point (vs speed), time to peak, peak decel, the shape of the release vs steering. A common pattern in less experienced drivers: hard initial stamp, then releasing too early and too linearly — the car is slower at turn-in than needed, but they compensate by braking earlier. The fix is usually a later point with a longer, progressive release (trail braking), not a "harder" stamp.

**Misconception:** "the driver with the highest peak brake pressure brakes best." Peak pressure says nothing about how much of the zone is spent at the limit, nor about the release, which is where most time is won or lost in medium and slow corners.

## L3 · Advanced

**Decomposing the deceleration.** Measured $g_{long}$ includes aero drag, engine braking, rolling resistance and gradient, not just friction brakes:

$$m\,a_x = F_{brakes} + D(V) + F_{engine}(gear, rpm) + F_{roll} + mg\sin\gamma$$

At 280 km/h on a GT3 drag alone is ~0.2–0.3 g ($C_DA \approx 0.8$–1.0 m²); on a formula car more. Comparing "braking effort" between a 280 km/h and a 150 km/h zone without removing $D$ is misleading. A useful channel is *tyre braking g* $= g_{long} - D(V)/mg$ using the coast-down $C_DA$.

**Brake energy and power.** Per zone: $E = \tfrac12 m (V_1^2 - V_2^2) - \int (D + F_{roll})\,ds$. Brake power $P = F_{brakes} V$ peaks at the start of the zone: on a GT3 from 280 km/h, ~1.6 g of tyre braking × 13.2 kN × 77.8 m/s ≈ **1.4–1.7 MW total**, ~0.5 MW per front disc. This connects braking data to temperature build-up (next lessons) and to pad wear modelling.

**Quickness and pitch.** The deceleration achievable in the first 0.1–0.3 s is limited by how fast load transfers to the front (pitch dynamics, front bump damping) and by how fast the tyre builds slip (relaxation length, ~0.2–0.5 m on slicks). A driver applying pressure faster than the platform can follow will lock the fronts (no ABS) or trigger ABS. Look at front lock spikes or ABS activity in the first 0.2 s: if present on every zone, the issue might be setup (front damping, bias, anti-dive) rather than driving.

**Statistical brake-point analysis.** For each zone, collect brake-point distance, approach speed, peak decel and minimum speed across laps. Regress brake-point distance on approach speed: the slope is ≈ $V/a_x$ per m/s (GT3 at 250 km/h and 1.6 g: ~1.2 m per km/h), so a measured slope far above that means the faster laps are also braked earlier relative to their speed. Residuals show genuine driver variation. Consistency (std. dev.) of brake point, after removing speed effects, of < 2–3 m is typical of a professional; > 5 m suggests a confidence or reference-point issue.

**Bias consistency diagnostics (Segers Figs 5.10–5.14):** combine $p_R$ vs $p_F$, bias vs $p_F$ and $p_F$ vs pedal travel plots. Free play shows at low pressure in all three; caliper deformation shows as a kink at a specific pressure in the first two; seal friction shows as hysteresis between application and release. These are hardware problems that look like driver inconsistency in the time domain.

## Key formulas

**Combined acceleration**

$$g_{comb} = \sqrt{g_{lat}^2 + g_{long}^2}$$


**Available braking while cornering (Segers Eq. 5.2)**

$$g_{long,max} = \sqrt{g_{max}^2 - g_{lat}^2}$$


**Deceleration decomposition**

$$m\,a_x = F_{brakes} + D(V) + F_{engine} + F_{roll} + mg\sin\gamma$$


**Brake jerk**

$$j = \frac{d\,g_{long}}{dt}$$


## Trackside takeaways

- Four questions: quickness, effort, brake point (vs approach speed), release/transition.
- Valleys in combined g during braking = unused grip, usually early braking or early release.
- Expected brake-point shift from approach speed: Δs ≈ V·ΔV/a_x (~6 m for 5 km/h on a GT3 at 250 km/h, 1.6 g). Only the residual is technique.
- Remove aero drag before comparing braking effort between high- and low-speed zones.
- Pedal travel vs pressure tracks pad wear and reveals knock-back and compliance.
- Peak pressure is not the metric; time at the limit and release quality are.

## By car category

### GT3

ABS means peak decel is often limited by the ABS rather than the driver; focus on brake point, release and ABS activity rather than peak pressure.

### One-make Cup

In Cup cars without ABS (e.g. the 992.1 Porsche Cup car), braking quickness and peak pressure modulation are strongly driver-dependent and a primary coaching topic.

### Formula 4

Typical training ground for braking technique: young drivers often stamp and release early. Combined-g valleys and brake-point consistency are the key coaching metrics.

### FIA F3

High downforce at the start of the zone allows very high initial pressure that must be bled off as speed drops; the release profile matters as much as the stamp.

### Hypercar (LMH/LMDh)

Braking data must be read with regen: total decel = friction + regen + drag. Use the BBW/torque channels, not hydraulic pressure alone, when comparing drivers.

### Super Formula

Very high peak deceleration with carbon brakes; time to peak and the release under high aero load are key performance differentiators.

## References

- Segers, Analysis Techniques for Racecar Data Acquisition, 2nd ed. (SAE 2014): §5.1 Braking Quickness, §5.2 Braking Effort, §5.3 Braking Points
- Segers, Analysis Techniques for Racecar Data Acquisition, 2nd ed. (SAE 2014): §5.6 Pedal Travel
- Segers, Analysis Techniques for Racecar Data Acquisition, 2nd ed. (SAE 2014): Ch. 14 (braking aggression and release smoothness metrics)
- Milliken & Milliken, Race Car Vehicle Dynamics (SAE 1995): Ch. 9 "g-g" Diagram
- Milliken & Milliken, Race Car Vehicle Dynamics (SAE 1995): Ch. 20 Driving and Braking
