# Tatuus T-318 (Formula Regional): setup adjustables and regulations

Formula Regional · FIA Formula Regional 1st Gen: FRECA (FR-19 variant, 2019–2025), Formula Regional Middle East (to 2025), Eurocup-3 (2023–2025) and other regional/national series; check which series still run it · Updated 2026-11-07
Source page: https://race-engineer-academy.vercel.app/cars/tatuus-t318-fr

The first-generation FIA Formula Regional car (2018 on). It is a carbon tub with halo, a **~270 hp 1.75 L turbo four** (Alfa Romeo/Autotecnica; the FRECA FR-19 variant used an Alpine-badged 1.8 L), a **Sadev SL-R82 6-speed sequential with LSD** and 13-inch slicks (Pirelli in FRECA, Hankook in Eurocup-3). For 2026 FRECA and FRME switched to the second-gen **Tatuus T-326** (Toyota-based 3-cylinder) and Eurocup-3 to a new Dallara chassis, so check whether your series still runs the T-318.

The FIA FR 1st Gen technical regulations are restrictive: **max 2-way dampers, no third elements, no bump stops of any kind, ARBs with dedicated positions only**, and conventional coil springs. Setup is therefore **springs, ARBs, dampers (where allowed), geometry and wings**. Compared with F4, there is **real downforce, an LSD and ~270 hp**, so diff work and aero-platform control appear for the first time. Without heave springs or bump stops, the platform has to come from the corner springs and ride height alone.

## Specification

- mass: 670 kg minimum (FIA FR 1st Gen; series may raise it up to 760 kg; power-to-weight must be ≥ 2.5 kg/bhp). At ~270 hp that rule means at least ~675 kg with driver, so series set their minimum to suit the engine; push-to-pass may temporarily go below the ratio
- power: ~270 hp (200 kW); optional push-to-pass up to +25 bhp for max 15 s per use
- engine: Alfa Romeo / Autotecnica Motori 1,742 cc turbo inline-4 (series-dependent; FR-19 used an Alpine/Renault 1.8 L)
- gearbox: Sadev SL-R82 6-speed sequential
- differential: Limited-slip differential (Sadev)
- tyres: 13-inch slicks, supplier series-specific (Pirelli in FRECA, Hankook in Eurocup-3); FRECA sizes 230/570 R13 front, 300/590 R13 rear (public spec sheets)
- aero: Front wing with adjustable flap and homologated gurneys; multi-position rear wing
- brakes: Brembo 4-piston calipers, ventilated discs
- electronics: Spec ECU and data logging; no TC/ABS
- chassis: Carbon monocoque, halo; double wishbone pushrod with twin dampers front and rear; wheelbase 2,750 mm

## What can be adjusted

| System | Parameter | Range | Freedom | Notes |
|---|---|---|---|---|
| Springs & ARB | Springs (front / rear) | Tatuus / series-approved rates; conventional coil springs only | limited by series rules | With no third element or bump stop, the corner springs carry all heave stiffness. Stiffer springs hold the floor and front wing at speed but cost mechanical grip over bumps and kerbs. This is the central trade-off of this car. |
| Springs & ARB | Front anti-roll bar | Dedicated positions only (sliding adjusters banned) | limited by series rules | Mid-corner balance. 1 step stiffer front ≈ +1–2 % front LLTD → more understeer, quicker response. |
| Springs & ARB | Rear anti-roll bar | Dedicated positions only | limited by series rules | Rotation vs traction. With an LSD the rear bar can be stiffer than on an open-diff F4 without inside-wheel spin. |
| Dampers | Dampers | Max 2-way adjustment allowed by regs; some series run non-adjustable spec units | limited by series rules | Public spec sheets describe Koni twin dampers as non-adjustable in some series, so check your championship. Where clicks are allowed, rebound is the main transient tool (entry stability front, exit squat rear). |
| Springs & ARB | Bump stops | Prohibited (FIA FR 1st Gen Art. 10.5.5) | fixed | Unlike GT3/F2, there are no bump rubbers to catch the platform. High-speed ride-height control comes only from springs and static ride height. |
| Geometry | Ride heights / rake | Pushrod adjustment; skid/plank limits | free | Main aero balance and platform tool. Without heave springs the front drops a lot under aero load: check front ride height at speed on the damper potentiometers before lowering further. |
| Geometry | Camber | Shims within mechanical range | free | Adjust on tyre temperature spread. The 13-inch tyre has a tall sidewall, so it is sensitive to camber and pressure. Small changes show clearly in temperature. |
| Steering | Toe (front / rear) | – | free | Rear toe-in for stability and traction. Front toe-out for turn-in. Change in small steps: at this weight toe effects are large. |
| Aero | Front wing flap / gurney | Homologated flap positions and gurney options | limited by series rules | Main front aero trim. One flap step is the standard fix for high-speed understeer when the mechanical balance is right. |
| Aero | Rear wing angle | Homologated positions | limited by series rules | Rear downforce and drag. Choose per track speed, then balance with front flap and rake. |
| Brakes | Brake bias | Cockpit knob | free | No ABS. Within a stop, falling downforce is handled by trail release, not bias. Over a race, adjust bias to the lock-up pattern in the data as fuel burns and tyres wear. |
| Engine | Push-to-pass | Up to +25 bhp, max 15 s per use (FIA FR regs; series sets number of uses) | limited by series rules | Strategy tool for attack and defence. Plan uses in the race brief. |
| Engine | Engine | Spec, sealed | fixed | No maps. Engines are allocated by the series. |
| Gearbox | Gear ratios | Spec ratios | fixed | Usually fixed by the series. |
| Differential | LSD settings | Preload/ramps within approved parts | limited by series rules | First car on the ladder where diff tuning matters. More preload/lock helps exit traction and entry stability but costs rotation in slow corners. |
| Tyres | Tyre pressures | Within the series tyre supplier's window | free | Key lever: target hot pressures per axle. Short races make warm-up as important as peak grip. |
| Tyres | Tyre allocation | Limited sets per event | set by BoP/homologation | Usually few new sets per weekend. Plan qualifying sets. |

## Regulations and BoP

- **FIA Formula Regional 1st Gen** technical regulations: spec Tatuus chassis; **max 2-way single-tube dampers, no third element, no bump stops, ARBs with dedicated positions only, conventional coil springs only**.
- **Minimum weight** 670 kg (series may raise it up to 760 kg); power-to-weight ≥ 2.5 kg/bhp.
- **Push-to-pass** permitted: max +25 bhp, max 15 s per use.
- **Tyres**: single supplier per series (Pirelli in FRECA, Hankook in Eurocup-3).
- For 2026 FRECA and FRME moved to the 2nd-gen Tatuus T-326 (Toyota-based engine) and Eurocup-3 to a new Dallara chassis.

## Engineering focus

- Platform control without third elements or bump stops (springs and ride height only)
- First real exposure to LSD tuning and aero balance for junior drivers
- Aero balance with front flap, rear wing and rake
- Tyre pressures on 13-inch tyres
- Junior driver development with data (braking, minimum speed, throttle)

## Typical complaints and first fixes

- High-speed understeer → Front flap up one step or more rake; check front ride height at speed
- Floor bottoming at high speed → Raise ride height or stiffer springs (no bump stops available)
- Mid-corner understeer in slow corners → Softer front ARB, check front camber and pressures
- Exit oversteer → Soften rear ARB, adjust LSD, coach throttle application
- Front lock-ups → Bias rearward, check brake temperatures and front pressures
