# Oreca 07 (LMP2): setup adjustables and regulations

LMP2 · ELMS LMP2, IMSA LMP2, Asian Le Mans Series, 24 Hours of Le Mans (LMP2 entries) · Updated 2026-11-07
Source page: https://race-engineer-academy.vercel.app/cars/oreca-07-lmp2

The Oreca 07 is the de-facto spec LMP2 car (since 2017). It is a carbon tub with the **spec Gibson GK428 4.2 L naturally aspirated V8**, an Xtrac 6-speed sequential with LSD, and homologated aero in two configurations: a **standard/high-downforce kit and a low-drag Le Mans kit**. Power has been cut since 2021 (restrictor and lower rev limit; ~536 hp in Le Mans trim). Since 2024 LMP2 races only at Le Mans in the WEC calendar, and ELMS gave back ~40 hp from 2024, so **check the current series' power spec**.

There is **no ABS** (TC available). Front torsion bars with heave elements give a full prototype platform. Setup is free within homologated parts and the cost-capped spare-part list. The engineering work is **platform and aero balance, braking without ABS, and long-run tyre degradation** with Pro-Am line-ups (most series require a Bronze or Silver driver).

## Specification

- mass: ~930–950 kg minimum depending on series/year (check ACO/IMSA regs)
- power: ~400 kW (~536–540 hp) in restricted Le Mans trim; ~580 hp in ELMS since 2024 (+40 hp, ELMS only); set by series, always check the current spec
- engine: Gibson GK428 4.2 L naturally aspirated V8 (spec, sealed)
- gearbox: Xtrac P1159 6-speed sequential, magnesium casing
- differential: Limited-slip differential (homologated)
- tyres: Goodyear (ELMS / Asian LMS), Michelin (IMSA); OZ 18-inch magnesium wheels
- aero: Homologated bodywork: standard/high-downforce kit and Le Mans low-drag kit; adjustable rear wing
- brakes: AP Racing carbon discs, Brembo 6-piston monobloc calipers; no ABS
- electronics: Cosworth steering wheel and electronics, TC, spec engine ECU
- chassis: Carbon-honeycomb tub; double wishbone pushrod; front torsion bars, rear coil-overs; wheelbase 3,005 mm

## What can be adjusted

| System | Parameter | Range | Freedom | Notes |
|---|---|---|---|---|
| Springs & ARB | Front torsion bars | From homologated range | limited by series rules | Front corner stiffness in roll and kerb compliance. Bar changes take time, so decide on the front torsion bar in early practice and fine-tune with ARB/heave after that. |
| Springs & ARB | Rear springs | From homologated range | limited by series rules | Rear corner stiffness: traction out of slow corners vs rear platform in fast ones. |
| Springs & ARB | Heave / third elements (front / rear) | Heave rates and packers from homologated range | limited by series rules | Platform control under aero load and braking. A stiffer front heave holds splitter height on long straights and through fast sweepers (Le Mans: Porsche Curves), but makes the car skip over bumps (Sebring). |
| Springs & ARB | Anti-roll bars (front / rear) | Homologated bars / blade positions | limited by series rules | Quickest mid-corner balance tool. Front ARB stiffer = more mid-corner understeer, quicker response in chicanes. |
| Dampers | Dampers | Homologated dampers; clicks free | limited by series rules | LS settings for platform and transients, HS for kerbs. Le Mans (chicane kerbs, long straights) and Sebring (bumps) need very different HS settings. |
| Geometry | Ride heights / rake | Within plank/skid rules | limited by series rules | Main aero balance tool. The underfloor makes most of the downforce, so front ride height is very sensitive. Check plank wear and ride height data at speed. |
| Geometry | Camber | Within mechanical range and tyre-supplier limits | free | Tune on tyre temperatures. For double/triple stints accept a little less peak grip to protect the inner shoulder. |
| Steering | Toe (front / rear) | – | free | Rear toe-in for stability. Reduce toe at Le Mans for drag and tyre temperature on the long straights. |
| Aero | Aero kit (Le Mans low-drag vs high-downforce) | Series-mandated per event | set by BoP/homologation | Le Mans requires the low-drag kit; ELMS runs the high-downforce kit. Balance and ride-height sensitivity change completely between kits, so don't carry setups across. |
| Aero | Rear wing angle / gurney | Homologated range and gurney options | limited by series rules | Balance tool. At Le Mans run minimum wing for top speed while keeping stability in the Porsche Curves and under braking for the chicanes. |
| Brakes | Brake bias | Cockpit balance bar | free | No ABS: within a stop, downforce bleed-off is handled by brake release, not bias; bias is trimmed over a stint for fuel load and tyre wear. Bronze drivers usually want more front bias for stability. |
| Brakes | Brake ducts | Homologated ducts; blanking allowed | limited by series rules | Carbon brakes need temperature: over-cooled = poor bite, inconsistent lock-ups and glazing. Night stints at Le Mans often need blanking. |
| Engine | Traction control | TC positions | free | More in the wet, at night on cold tyres, and for Bronze drivers. |
| Engine | Engine power | Spec engine; power set by series rules (restrictor / rev limit) | set by BoP/homologation | Not a setup item. It affects gearing usage and fuel per lap. |
| Gearbox | Gear ratios | Homologated ratios | set by BoP/homologation | Effectively fixed. Choose shift points and lines instead. |
| Differential | Differential preload | Within homologated components | limited by series rules | Entry stability vs rotation. More preload helps Bronze drivers on entry but costs rotation in slow corners. |
| Tyres | Tyre pressures | Within supplier window | free | Key lever. For double-stints, start pressures must allow for pressure build over a long run and cooler night conditions. |
| Tyres | Tyre allocation | Limited sets per event | set by BoP/homologation | Le Mans strategy is built around double/triple-stinting tyres. |

## Regulations and BoP

- **ACO/IMSA LMP2**: four chassis were homologated, but in practice almost every entry is an Oreca 07.
- **Spec engine** (Gibson GK428), sealed; power reduced since 2021 (restrictor, rev limit), with ELMS restoring ~40 hp.
- **Aero**: homologated high-downforce and Le Mans low-drag kits.
- **No ABS**; traction control available.
- **Tyres**: Goodyear (ELMS/Asian LMS), Michelin (IMSA).
- **Cost cap** on parts; Pro-Am driver line-up rules (minimum drive times for the Bronze/Silver driver).

## Engineering focus

- Platform control with torsion bars, heave elements and packers
- Aero kit choice and balance (Le Mans low-drag vs high-downforce)
- Braking without ABS: bias, cooling, driver coaching
- Long-run tyre degradation and double-stinting
- Pro-Am driver compromise in setup and strategy

## Typical complaints and first fixes

- Front lock-ups into slow corners → Bias rearward, coach brake release, check brake temperatures (blank ducts if cold)
- High-speed understeer → Check front ride height at speed against the aero map. If above the stall region: soften front heave / remove front packer or stiffen rear heave to keep rake, lower front ride height. Stiffen the front only if the floor stalls or grounds
- Snap oversteer on exit → TC up one step, soften rear ARB
- Instability at Le Mans (Porsche Curves, braking zones) → One step more wing, rear toe-in, check rear heave
- Tyre degradation in double stints → Lower start pressures, reduce camber slightly, soften rear ARB
