# Ligier JS P325 (LMP3): setup adjustables and regulations

LMP3 · ELMS LMP3, Michelin Le Mans Cup, Asian Le Mans Series, IMSA VP Racing SportsCar Challenge · Updated 2026-11-07
Source page: https://race-engineer-academy.vercel.app/cars/ligier-js-p325

Ligier's third-generation LMP3 (from 2025). It runs the **spec Toyota V35A 3.4 L twin-turbo V6 (~470 hp)** that replaced the Nissan V8, with an Xtrac 6-speed sequential gearbox. The chassis is a carbon tub with **4-way Öhlins TTX40 dampers, third elements front and rear and an adjustable ARB system**. It has real prototype downforce, **no ABS**, and traction control is available. Minimum weight is 1,000 kg.

LMP3 is the ACO's entry prototype class: cost-capped, with spec engine, gearbox and Michelin tyres and homologated aero. For an engineer it is the first car where **heave/third-element platform control, ride-height-sensitive underfloor aero and brake management without ABS** all matter at the same time. Many drivers step up from GT4/GT3, so driver development (trail-braking without ABS, trusting downforce) is part of the job.

## Specification

- mass: 1,000 kg minimum (ACO Gen3 LMP3)
- power: ~470 hp (350 kW); spec engine
- engine: Toyota V35A-FTS 3,445 cc V6 twin-turbo, racing version developed by ORECA with IHI turbos
- gearbox: Xtrac P1152 6-speed sequential
- differential: Limited-slip (spec drivetrain)
- tyres: Michelin (spec); 18-inch wheels, 13-inch wide
- aero: Homologated LMP3 bodywork; adjustable rear wing
- brakes: Brembo 6-piston calipers front and rear, ~355–360 mm discs; no ABS
- electronics: Spec engine ECU with TC; data logging; power steering
- chassis: HP Composites carbon monocoque with Zylon side panels; double wishbone pushrod; wheelbase 2,860 mm; 100 L tank

## What can be adjusted

| System | Parameter | Range | Freedom | Notes |
|---|---|---|---|---|
| Springs & ARB | Front anti-roll bar | Adjustable ARB system (homologated parts) | limited by series rules | Mid-corner balance tool. On a prototype, roll also changes floor height at the edges, so ARB changes slightly affect aero too. 1 step stiffer front ≈ +1–2 % front LLTD → more mid-corner understeer. |
| Springs & ARB | Rear anti-roll bar | Adjustable ARB system (homologated parts) | limited by series rules | Rotation vs traction with turbo torque. Stiffen in single steps. Soften for slow-corner exits and the wet. |
| Springs & ARB | Corner springs | From Ligier range | limited by series rules | Mainly roll and kerb compliance, because the third elements carry much of the heave load. Softer corners help mechanical grip at bumpy tracks. |
| Springs & ARB | Third elements (front / rear) | Third spring rates and packers from Ligier range | limited by series rules | Controls ride height under aero load and braking without adding roll stiffness. A stiffer front third (or more packer) holds front ride height in heavy braking and at high speed, which keeps aero balance stable. The price: the front runs higher at speed, so front load drops and balance moves rearward unless the floor was stalling. Too stiff makes the car skate over bumps. |
| Dampers | Dampers (Öhlins TTX40, 4-way) | LS/HS bump and rebound clicks | free | Through-rod 4-way dampers. LS bump/rebound control platform and transients (pitch on braking, turn-in). HS settings for kerbs and bumps (Sebring/Portimão vs Paul Ricard). Change 2 clicks at a time and check on damper-velocity histograms. |
| Geometry | Ride heights / rake | Adjustable within plank/skid rules | limited by series rules | Main aero balance tool. The underfloor is sensitive to front ride height: 1 mm at the front moves balance noticeably more than 1 mm at the rear. Check plank wear after each run. |
| Geometry | Camber | Within mechanical range and Michelin guidance | free | Tune on tyre temperature spread after a consistent run. More front camber for lateral grip, less for braking stability (important without ABS). |
| Steering | Toe (front / rear) | – | free | Rear toe-in for high-speed stability and power-down. Front toe-out for turn-in. Toe also costs top speed, so reduce it for Le Mans-type tracks. |
| Aero | Rear wing angle | Homologated range | limited by series rules | Balance tool for high-speed corners. Run low wing at Le Mans (Road to Le Mans) and more at twisty circuits. Keep the balance with rake. |
| Brakes | Brake bias | Cockpit balance bar | free | No ABS, so this is critical for lock-ups. As speed falls in the stop, downforce and grip fall, so the driver must release pressure (trail release); bias alone cannot fix that. Over a stint, adjust bias to the lock-up pattern seen in the data (tyre wear, fuel load, low-grip surfaces) rather than following a fixed rule. |
| Brakes | Brake ducts | Homologated ducts; blanking allowed | limited by series rules | Keep discs and pads in their temperature window. Over-cooled brakes lock more easily because pad bite is inconsistent. |
| Engine | Traction control | TC positions on spec ECU | free | Set for consistent exits. Increase in the wet and as rear tyres degrade. Compare wheel-speed slip with TC cut in the data. |
| Engine | Engine power | Spec, sealed | fixed | Equal power across chassis brands. Any balancing between chassis is done by the series, not the team. |
| Gearbox | Gear ratios | Spec ratios | fixed | Not adjustable. Optimise shift points and corner lines instead. |
| Differential | Differential preload | Within spec drivetrain parts | limited by series rules | More preload = more entry stability and power-on understeer. Less = more rotation but snappier exits. Change between events rather than sessions. |
| Tyres | Tyre pressures | Within Michelin window | free | Key lever in a spec class. Hit hot targets per axle. In Le Mans Cup sessions are short, so warm-up speed matters as much as peak grip. |
| Tyres | Tyre allocation | Limited sets per event | set by BoP/homologation | Plan new vs used sets for qualifying and race, including Bronze driver stints. |

## Regulations and BoP

- **ACO LMP3 Gen3** (2025+): homologated chassis (Ligier, Duqueine, Ginetta, ADESS), **spec Toyota V35A engine** (homologated to end of 2029), spec gearbox and tyres.
- **Cost cap**: complete car ~299,000 EUR; powertrain ~89,200 EUR (ELMS announcement).
- **No ABS**; traction control available.
- **Tyres**: Michelin, allocation-limited.
- The series can balance different chassis (weight/aero); there is no team-level engine adjustment.

## Engineering focus

- Platform control with third elements, packers and 4-way dampers
- Brake management without ABS: bias, cooling and driver brake-release coaching
- Aero balance via front ride height, rake and wing
- Tyre pressure targeting on spec Michelins in short sessions
- Driver development: stepping up from GT to prototype downforce

## Typical complaints and first fixes

- Front lock-ups into slow corners → Bias rearward a step, coach brake release as downforce falls, check front pressures/brake temperatures
- High-speed understeer → Check front ride height at speed against the aero map. If above the stall region: soften the front third / remove front packer or stiffen the rear third to keep rake, lower front ride height slightly. Stiffen the front only if the floor stalls or the skid touches
- Snap oversteer on exit → TC up one step, soften rear ARB, reduce diff preload change only if entry is fine
- Bottoming / porpoising on straights → Raise ride height, stiffer thirds, check plank wear
- Rear unstable in fast direction changes → More rear wing, rear toe-in, check rear third not too soft
