# Ferrari 296 GT3: setup adjustables and regulations

GT3 · GT World Challenge (Pirelli), IMSA GTD/GTD Pro (Michelin), FIA WEC LMGT3 (Goodyear), DTM and national GT3 · Updated 2026-11-07
Source page: https://race-engineer-academy.vercel.app/cars/ferrari-296-gt3

Ferrari's GT3 since 2023 (Evo update from 2026). It has a **mid-engined 3.0 L 120° twin-turbo V6** (hybrid removed) and an Xtrac 6-speed transverse sequential gearbox. Compared to the 488 GT3 it has a shorter wheelbase and a lower, more compact engine, with a strong underbody/diffuser aero concept. The **2026 Evo** brings revised suspension kinematics, a new ratio cascade, new splitter/floor/diffuser, more front brake cooling (+20 % airflow) and a rear wing that can be adjusted with a single screw, quick enough to change at a pit stop.

As with every GT3, the **engine output and weight are set by BoP** (turbo boost and weight), so setup work concentrates on the aero platform, tyres and drivability for mixed Pro/Am line-ups.

## Specification

- mass: ~1,250 kg dry without fuel/driver (Ferrari figure); race minimum set by BoP
- power: ~600 cv nominal; actual output set by BoP (boost)
- engine: F163 2,992 cc 120° V6 twin-turbo, turbos inside the V, mid-mounted
- gearbox: Xtrac 6-speed transverse sequential, magnesium casing; Evo: new ratio cascade
- differential: Mechanical limited-slip differential (preload adjustable)
- tyres: Series spec: Pirelli (GTWC/DTM), Michelin (IMSA), Goodyear (WEC LMGT3)
- aero: Underbody/diffuser-led aero, swan-neck rear wing; Evo: new splitter, floor, diffuser, LMGT3-derived rear arches and quick-adjust wing
- brakes: Steel discs and racing calipers, racing ABS; Evo: +20 % front brake airflow
- electronics: Racing ABS and TC (driver rotaries), homologated ECU and data logging
- chassis: Aluminium chassis with FIA cage; double wishbones front and rear on Evo

## What can be adjusted

| System | Parameter | Range | Freedom | Notes |
|---|---|---|---|---|
| Springs & ARB | Front anti-roll bar | Homologated bars / blade positions | limited by series rules | First mid-corner balance tool. 1 step stiffer ≈ +1–2 % front LLTD → more understeer mid-corner, sharper response in quick direction changes. |
| Springs & ARB | Rear anti-roll bar | Homologated bars / positions | limited by series rules | Turbo torque out of slow corners makes rear roll stiffness a traction trade-off. Soften for traction, stiffen for rotation. |
| Springs & ARB | Springs (front / rear) | Rates from homologated / manufacturer range | limited by series rules | Platform choice. Stiffer front holds the splitter height under braking. Ride-frequency targets for GT3 are typically ~2.5–3.5 Hz. |
| Dampers | Dampers | Multi-way adjustable homologated dampers (LS/HS bump and rebound) | free | Clicks are free within the homologated unit. Use LS rebound for entry stability and LS bump for platform. Use HS settings for kerbs and bumps. |
| Geometry | Ride heights (front / rear) and rake | Free within homologated travel; some series/BoP set minimum heights | limited by series rules | The main aero balance tool on a GT3: +1 mm rear ride height (or -1 mm front) moves aero balance forward roughly 0.3–0.5 %. Check BoP/series minimum heights and plank/skid rules before chasing rake. Always re-check heights hot, with fuel load, as measured on the setup plate. |
| Geometry | Camber (front / rear) | Typically −3.5 to −4.5° front, −2.5 to −3.5° rear | free | Set on tyre-temperature spread (aim ~8–12 °C inner-to-outer on hot pit temps) and on tyre-supplier camber limits where they exist. Front camber is a peak-lateral tool; too much costs braking stability and inner-shoulder wear. |
| Steering | Toe (front / rear) | Front ~0 to 2 mm total out; rear ~2–4 mm total in | free | Rear toe-in is a stability tool (more = more stable entry and power-down, but more drag and rear temperature). Front toe-out sharpens initial turn-in. Change in 0.5 mm steps — GT3s are very sensitive to rear toe. |
| Springs & ARB | Bump stops / packers | Packer thickness and bump-rubber type within supplier range | free | On high-downforce GT3s the bump rubber is effectively the aero platform spring at high speed. Adding packer lowers the speed or load at which the stop engages, so the axle gets stiffer at high speed and under heavy braking. More front packer holds the front up: less front downforce (aero balance moves rearward) and more front roll stiffness, so usually more high-speed understeer. To cure high-speed understeer, remove front packer or add rear packer to hold rake. Add front packer only when ride-height and aero-map data show the splitter/floor stalling or the skid touching. |
| Aero | Rear wing angle | Homologated range; Evo wing re-set with a single screw (quick pit-stop change); BoP may cap | limited by series rules | Each step typically shifts aero balance ~1 % rearward and costs some top speed. BoP may cap the usable range. Balance wing against rake: wing for high-speed stability, rake/ride height for overall platform. |
| Brakes | Brake bias | Driver-adjustable balance bar (cockpit knob), typically ~54–60 % front | free | Move rearward for rotation on entry, forward for stability and to protect the rear under ABS. On ABS cars the bias also changes which axle ABS intervenes on first — check ABS activity per axle in the data, not just lock-ups. |
| Brakes | Master cylinder sizes | From the homologated/manufacturer list | limited by series rules | Changes pedal-force-to-pressure gain and the bias range available. Used to suit driver pedal feel (gentlemen drivers often want lower effort) rather than as a balance tool. |
| Brakes | Brake ducts / blanking | Homologated ducts; blanking/tape allowed | limited by series rules | Target disc and pad windows from the brake supplier. Over-cooling at cold tracks kills initial bite; under-cooling at Monza/Bahrain-type tracks causes fade and pad glazing. |
| Brakes | Pad compound | Manufacturer-approved compounds; series may restrict | limited by series rules | Endurance pads trade initial bite for wear and temperature stability. Change pads with care: driver pedal reference and ABS calibration both move. |
| Engine | Power / torque (restrictor, boost, power map) | Set by BoP each event | set by BoP/homologation | Not a setup tool. The engineer manages around it: gearing, fuel per lap and drag level. Some series use torque sensors to police power curves. |
| Engine | Engine / fuel maps | Homologated maps only (e.g. race, fuel-save, safety car) | limited by series rules | Fuel-save maps and lift-and-coast targets are strategy tools. The torque curve itself is homologated. |
| Engine | Traction control | Multi-position TC (rotary) | free | TC level is a real handling tool on exit: more TC hides poor traction, but heats the rears less. Set a baseline, then let the driver step through it as the tyres degrade. In data, compare wheel-speed slip with TC cut. |
| Brakes | ABS level | Multi-position racing ABS | free | Higher intervention = more stable but longer stops; lower = more aggressive. Wet races and worn tyres usually want more. Gentlemen drivers often benefit from a higher setting than pros. |
| Gearbox | Gear ratios / final drive | Homologated set; usually one ratio set per car | set by BoP/homologation | Effectively fixed. Gearing problems are solved through shift points and driving lines, not new ratios. |
| Tyres | Tyre pressures | Hot targets from the tyre supplier; some series enforce minimum pressures | free | GT3 tyres want a narrow hot window (often ~1.8–2.0 bar hot, supplier-dependent). Start pressures are chosen to hit target hot pressure by lap 2–3. Pressure is a balance tool only in small steps (~0.05 bar). |
| Tyres | Tyre compound / allocation | Single spec per series (Pirelli in GTWC, Michelin in IMSA, Goodyear in WEC LMGT3); limited sets per event | set by BoP/homologation | Plan the allocation: which sets for qualifying, which used sets for race stints and driver changes. |
| Geometry | Ballast / minimum weight | BoP weight, plus success ballast in some series | set by BoP/homologation | Ballast position (where the series allows) can be used to help weight distribution, but the amount is set by BoP. |
| Differential | Differential preload / ramps | Within homologated components | limited by series rules | Higher preload = more stable entry and power-on understeer. Lower = better rotation but snappier. Change between events rather than sessions. |
| Aero | Front dive planes / gurney options | Homologated options only | set by BoP/homologation | Where homologated options exist, they are used to trim front aero to match a wing change. |

## Regulations and BoP

- **Homologated GT3** (FIA/SRO): bodywork, aero devices, suspension geometry and gearbox are homologated. Only listed options may be used.
- **BoP**: weight, turbo boost (power curve), and in some series fuel capacity/stint energy and ride-height or wing limits. Adjusted between events by SRO/IMSA/ACO.
- **Tyres**: one supplier per series (Pirelli GTWC/DTM, Michelin IMSA, Goodyear WEC). Allocation-limited; WEC also bans tyre warmers.
- **Evo kit (2026)**: new aero, suspension kinematics and gearbox ratios homologated as an evolution. The original 2023 spec and the Evo can carry different BoP.
- Driver ratings (FIA Platinum/Gold/Silver/Bronze) determine Pro/Pro-Am/Am categories and minimum drive times.

## Engineering focus

- Aero platform: ride height/rake vs wing (Evo quick-adjust wing allows balance changes at pit stops)
- Turbo torque delivery and traction on exit: TC, rear ARB, diff preload
- Tyre-pressure management with series-specific tyres and allocation limits
- BoP-aware strategy: fuel per lap, stint length, drag level choice
- Making the car drivable for Bronze/Silver drivers without compromising the Pro

## Typical complaints and first fixes

- Mid-corner understeer → Soften front ARB or stiffen rear, check front camber/pressure on tyre temps
- Exit wheelspin / power oversteer with turbo torque → TC up one step, soften rear ARB, lower diff preload ramp on drive only if available
- High-speed understeer, low-speed balanced → First check front ride height at speed against the aero map. If the front is above the stall region: remove front packer or add rear packer to keep rake, or reduce wing a step. Add front packer only if data shows the splitter stalling or the skid touching
- Instability under braking into slow corners → Bias forward, more rear toe-in, ABS up one step
- Front brakes overheating (pre-Evo cars) → Open ducts fully, check pad choice; Evo addresses this with +20 % cooling flow
