# Dallara F3 2025: setup adjustables and regulations

FIA F3 · FIA Formula 3 Championship (F1 support) · Updated 2026-11-07
Source page: https://race-engineer-academy.vercel.app/cars/dallara-f3-2025

The third-generation FIA F3 car (2025 on): a Dallara chassis with a new aero package optimised for following, **16-inch Pirelli tyres**, the carry-over **Mecachrome 3.4 L naturally aspirated V6 (380 hp @ 8,000 rpm)**, a **3Mo 6-speed gearbox** and F1-style hydraulic **DRS**. Teams receive everything from the series promoter. The FIA technical regulations list exactly what may be changed: **wing configurations from the user manual, springs/torsion bars from the supplied list, damper clicks free and valves only from the manual range, diff ramps from approved parts plus preload shims, camber within Pirelli limits**.

**Gear ratios are defined by the FIA for each competition**, so teams do not choose them. The minimum mass is **729 kg without fuel** (including driver; 2026 regs, 722 kg in 2025). With 30 identical cars, small setup changes and data comparison with teammates decide grid positions measured in hundredths.

## Specification

- mass: 729 kg minimum without fuel, including driver (2026 FIA F3 technical regulations; 722 kg in 2025)
- power: 380 hp @ 8,000 rpm; 420 Nm
- engine: Mecachrome V634 3.4 L 95° V6 naturally aspirated
- gearbox: 3Mo 6-speed longitudinal, electro-hydraulic paddle shift; ratios defined per competition
- differential: Limited-slip; ramp angles and preload adjustable within approved parts
- tyres: Pirelli P Zero 16-inch slicks (three compounds in the range) and Cinturato wets
- aero: New 2025 aero package optimised for following; hydraulic DRS; HDF rear wing only raced at Monaco
- brakes: Spec brake system from the promoter
- electronics: Spec ECU and data acquisition; FIA ADR
- chassis: Carbon/kevlar monocoque, halo; double wishbone pushrod with twin dampers

## What can be adjusted

| System | Parameter | Range | Freedom | Notes |
|---|---|---|---|---|
| Springs & ARB | Springs / torsion bars | Only those specified by Dallara and supplied by the F3 promoter | limited by series rules | Platform vs mechanical grip. A stiffer front holds front-wing height under braking (front wing is ground-effect sensitive). Softer helps over kerbs and at bumpy street-type tracks. |
| Springs & ARB | Anti-roll bars (front / rear) | Within the Dallara range | limited by series rules | Main mid-corner balance tool. 1 step stiffer front ≈ +1–2 % front LLTD → more mid-corner understeer. |
| Springs & ARB | Packers / bump rubbers | Only solid packers, metal wool washers and bump rubbers on damper shafts | limited by series rules | High-speed platform tool: sets where travel stops under aero load. Use to stop the car touching down at the end of long straights. |
| Dampers | Damper clicks | Free within the adjustment range of the supplied damper | free | Transient and kerb tool. LS rebound for entry stability, LS bump for turn-in/platform. Confirm with damper-velocity histograms. |
| Dampers | Damper valves | Only valves listed in the Dallara user manual | limited by series rules | Event-level choice (street vs permanent circuit). |
| Geometry | Ride heights / rake | Pushrod adjustment; plank wear rules | free | Main aero balance tool. More rake = more front bias and more total load, up to the point where the floor loses performance. Check plank wear. |
| Geometry | Camber | Within supplier range and Pirelli maximum camber | limited by series rules | Pirelli's maximum camber is policed at all times. Most teams run near the limit for qualifying and back off for tyre life only if needed. |
| Steering | Toe (front / rear) | – | free | Rear toe-in for stability and traction. Front toe for turn-in. Toe also adds tyre temperature: useful for warm-up, harmful for long-run overheating. |
| Aero | Front wing configuration | Configurations from the Dallara user manual | limited by series rules | Main front aero trim for high-speed balance. |
| Aero | Rear wing configuration | User-manual configurations; HDF only raced at Monaco | limited by series rules | Track downforce/drag choice. It also changes how much DRS gains. |
| Aero | DRS | Hydraulic DRS, enabled by race control | fixed | Not a setup item, but the rear wing choice changes DRS effectiveness. |
| Brakes | Brake bias | Driver-adjustable | free | No ABS. Drivers adjust bias through a stint as fuel and tyre grip change. Rear lock-ups on low-fuel qualifying laps are common. |
| Brakes | Brake duct taping | Tape allowed for temperature optimisation only | limited by series rules | Keep brakes in their temperature window at cold events. |
| Engine | Engine | Spec, sealed | fixed | No maps or power adjustment. |
| Gearbox | Gear ratios | Defined by the FIA for each competition | fixed | Same ratios for all cars at each event. Gearing becomes a line and shift-point question. |
| Differential | Diff ramp angles / preload | Ramp parts from the promoter; preload spacers/shims | limited by series rules | Main entry/exit tool beyond ARBs. More coast lock = stable entry but understeer. More drive lock = traction but power understeer. |
| Tyres | Tyre pressures | Above Pirelli minimum at all times | limited by series rules | Minimum pressures are policed, so start pressures have to keep the tyres above the minimum. Pressure is not a free balance tool. |
| Tyres | Tyre allocation | Limited Pirelli sets per event | set by BoP/homologation | Very few new sets: one-lap qualifying preparation (out-lap, push-lap timing) is a big part of the engineer's job. |

## Regulations and BoP

- **FIA F3**: spec Dallara F3 2025 supplied by the promoter; Type 1/2/3 part classification controls modifications.
- **Minimum mass** 729 kg without fuel (2026 regs; 722 kg in 2025).
- **Gear ratios** defined by the FIA for each competition.
- **Springs/torsion bars, damper valves, diff ramps**: only from approved/promoter range; damper clicks free.
- **Wings**: user-manual configurations only; HDF only raced at Monaco.
- **Tyres**: Pirelli 16-inch; minimum pressures and maximum camber policed.

## Engineering focus

- Fine-tuning a spec car where small changes decide qualifying in a 30-car field
- Tyre preparation and management (minimum pressures, max camber, few sets)
- Data comparison vs teammates (braking, minimum speed, throttle)
- Diff ramps and ARBs for entry/exit balance
- Race strategy with DRS and sprint/feature formats

## Typical complaints and first fixes

- Mid-corner understeer in slow corners → Softer front ARB, reduce diff coast lock, check front pressures
- High-speed understeer → Front wing configuration step up or more rake
- Rear tyre overheating in the race → Less rear toe-in, softer rear ARB, coach throttle application
- Front lock-ups → Bias rearward, check brake temperatures (tape ducts if cold)
- Exit oversteer → Adjust diff drive ramp, softer rear ARB, more rear wing
