# Dallara F2 2024: setup adjustables and regulations

FIA F2 · FIA Formula 2 Championship (F1 support) · Updated 2026-11-07
Source page: https://race-engineer-academy.vercel.app/cars/dallara-f2-2024

The third-generation FIA F2 car (2024–2026+). It is a Dallara chassis with **ground-effect-influenced floor, F1-style wings, DRS and 18-inch Pirelli tyres**, powered by the **Mecachrome V634T 3.4 L single-turbo V6 (~620 hp)** through a Hewland 6-speed. Front suspension uses torsion bars and the rear coil springs, both with twin dampers. Carbon brakes (Carbone Industrie discs/pads, Brembo calipers).

Like F3, everything comes from the promoter, and the FIA technical regulations define exactly what can change. **Gear ratios are specified by the FIA for each competition**. Springs and torsion bars come only from the supplied list, damper valves only from the user-manual range, diff ramp parts from the promoter (plus preload shims), and wing configurations only from the user manual. The HDF rear wing can only be raced at Monaco. Pirelli **minimum pressures and maximum camber** are policed. Minimum mass is **793 kg without fuel** (2026 regs; 785 kg in 2024). Most of the performance difference comes from **tyre management (especially in the sprint/feature race format with mandatory pit stop), platform and diff, and the driver**.

## Specification

- mass: 793 kg minimum without fuel, including driver (2026 FIA F2 technical regulations; 785 kg in 2024)
- power: ~620 hp @ 8,750 rpm; ~583 Nm
- engine: Mecachrome V634T 3.4 L V6 single turbo
- gearbox: Hewland 6-speed sequential, paddle shift; ratios defined by FIA per competition
- differential: Limited-slip; ramp angles from promoter parts, preload via spacers/shims
- tyres: Pirelli P Zero 18-inch slicks (two compounds per event), Cinturato wets; OZ wheels
- aero: Ground-effect-influenced floor, F1-style front wing, rear wing with DRS; HDF rear wing only raced at Monaco
- brakes: Carbone Industrie carbon discs and pads, Brembo 6-piston calipers; spec parts only
- electronics: Spec ECU and data acquisition; common ECU configuration files; FIA ADR
- chassis: Carbon/aluminium honeycomb monocoque, halo; front torsion bars, rear springs, twin dampers; wheelbase 3,135 mm

## What can be adjusted

| System | Parameter | Range | Freedom | Notes |
|---|---|---|---|---|
| Springs & ARB | Front torsion bars | Only bars specified by Dallara and supplied by the F2 promoter | limited by series rules | Front ride and roll stiffness. Stiffer front holds the floor and front wing at a stable height (ground-effect floor is sensitive to front ride height) but reduces mechanical grip over bumps and kerbs. |
| Springs & ARB | Rear springs | Only springs supplied by the F2 promoter | limited by series rules | Rear platform and traction. With ~620 hp turbo torque, a softer rear helps traction out of slow corners at the cost of rear ride-height control at speed. |
| Springs & ARB | Anti-roll bars (front / rear) | Within Dallara range | limited by series rules | Mid-corner balance tool. 1 step stiffer front bar ≈ +1–2 % front LLTD: more mid-corner understeer, quicker response. |
| Springs & ARB | Packers / bump rubbers | Only solid packers, metal wool washers and bump rubbers on damper shafts | limited by series rules | Main high-speed platform tool. Packers decide where the floor stops dropping under load. Too much front packer causes snappy high-speed understeer/oversteer transitions as the car goes onto the stops. |
| Dampers | Damper clicks | Free within the adjustment range of the supplied damper | free | The fine-tuning tool. LS rebound for entry stability, LS bump for platform and turn-in, HS for kerbs. Change 2 clicks at a time and confirm on damper-velocity histograms. |
| Dampers | Damper valves | Only valves listed in the Dallara user manual | limited by series rules | Event-level choice (e.g. street circuit vs smooth permanent track). Valve changes need dyno checks. |
| Geometry | Ride heights / rake | Pushrod adjustment; plank 5 mm nominal, wear limits apply | free | Main aero balance tool on a floor-influenced car. Lower and more rake = more downforce but more pitch sensitivity and plank wear. Check plank wear after every run. |
| Geometry | Camber | Spacers in hub/upper wishbone mount, supplier range, within Pirelli max camber | limited by series rules | Pirelli max camber is policed. Running at the limit is common, so the real camber choice is often how far below the limit you go for tyre life in the feature race. |
| Steering | Toe (front / rear) | – | free | Rear toe-in for stability and traction. Front toe-out for turn-in. Toe also heats tyres: reduce for long feature-race stints if overheating. |
| Aero | Front wing configuration | Only configurations described in the Dallara user manual | limited by series rules | Front flap angle is the main balance trim between sessions. Pair with rear wing to keep the aero balance target. |
| Aero | Rear wing configuration | User-manual configurations; HDF only raced at Monaco | limited by series rules | Track-specific downforce/drag level. Low-drag at Monza/Baku. DRS effectiveness depends on the wing chosen. |
| Aero | DRS | Race-control enabled | fixed | Not a setup item, but the wing choice changes DRS speed gain. |
| Brakes | Brake bias | Driver-adjustable | free | Carbon brakes need temperature. Bias rearward for rotation but watch rear lock-ups on low-fuel qualifying laps. |
| Brakes | Brake duct taping | Ducts may be partially or fully taped for temperature only | limited by series rules | Carbon discs below their window give poor bite. Tape at cold tracks, open fully at Bahrain/Monza. |
| Engine | Side-pod / radiator taping | Tape on stone guard or plate on radiator face for temperature only | limited by series rules | Cooling vs drag. Small but real gain at cold events. |
| Engine | Engine | Spec, sealed; common ECU configuration | fixed | No maps or power adjustment. |
| Gearbox | Gear ratios | Defined by the FIA for each competition | fixed | Same ratios for all cars at each event. Gearing problems become shift-point and line problems. |
| Differential | Diff ramp angles / preload | Ramp parts from promoter; preload spacers ground / circular steel shims | limited by series rules | Main entry/exit tool beyond ARBs. More coast ramp lock = entry stability but understeer. More drive lock = traction but power understeer. Preload affects low-speed behaviour. |
| Tyres | Tyre pressures | Above Pirelli minimum at all times (TPMS monitored) | limited by series rules | Minimum pressures are policed. Start pressures are set so the tyres never drop below the minimum. Pressure is not a free balance tool. |
| Tyres | Tyre allocation / compounds | Two Pirelli compounds per event; limited sets | set by BoP/homologation | Mandatory use of both compounds in the feature race. Plan which sets to save for the race. |
| Geometry | Ballast | Only in locations specified by Dallara | limited by series rules | Weight distribution trimming within allowed positions. |

## Regulations and BoP

- **FIA F2**: spec Dallara F2 2024; all parts from the F2 promoter. Type 1/2/3 parts classification defines what can be modified.
- **Minimum mass** 793 kg without fuel (2026 regs; 785 kg in 2024).
- **Gear ratios** defined for each competition by the FIA.
- **Springs/torsion bars, damper valves, diff ramps**: only from approved/promoter range.
- **Wings**: user-manual configurations only; HDF rear wing only raced at Monaco.
- **Tyres**: Pirelli; minimum pressures and maximum camber from Pirelli's technical preview are policed. No tyre heating devices.
- **Brakes**: only promoter-supplied discs and pads.

## Engineering focus

- Tyre management over the feature race (two compounds, mandatory stop) and sprint race on used tyres
- Platform control: torsion bars, packers, ride height and rake for a floor-sensitive car
- Diff ramp/preload for entry stability vs rotation
- Carbon brake temperature management with duct taping
- Data comparison vs teammates in an identical car

## Typical complaints and first fixes

- Mid-corner understeer in slow corners → Soften front ARB, reduce diff coast lock, check front pressures not too high
- High-speed instability / car "touches down" → Raise ride height or add packer, check plank wear and damper potentiometer data
- Rear tyre overheating in feature race → Reduce rear toe-in, soften rear ARB, coach smoother throttle; adjust diff drive ramp
- Front lock-ups on low-fuel qualifying laps → Bias rearward slightly, check brake temperatures (tape ducts if cold)
- Power oversteer out of slow corners → Softer rear spring/ARB, adjust diff drive ramp, more rear wing
